User's Manual

ManualsBrandsRis ManualsElectronicsSmoke Detector

868 MHz & 433 MHz

Wireless Supervised Photoelectric

Smoke Detectors

Installation Instructions

GENERAL DESCRIPTION

The Smoke Detectors are battery-powered

photoelectric smoke detectors with a built-in supervised

wireless transmitter.

When sufficient smoke is detected or the test feature is

operated, the detector will sound its alarm horn and the

transmitter will send an ALARM message. If the alarm

condition remains, the message will be repeated 2 or

more times (with 65 second intervals). The Alarm

output in the receiver will remain activated until the

alarm condition is cleared.

The smoke alarm provides the following features:

Smoke Alarm/base lock discourages unauthorized

removal of the smoke alarm by requiring a screwdriver

to remove the alarm from the base.

CleanMe™ Self-diagnostics monitors its own

sensitivity and operational status. If the smoke alarms

drifts out of the sensitivity range or fails internal

diagnostics, it extinguishes its LED

Internal Signal Outputs

The smoke alarm provides the following signals for

interfacing:

• Alarm

• Alarm restore

• Low battery

• Maintenance alert (Visible only)

Selecting a Location

Selecting a suitable location is critical to the operation of

smoke alarms. This equipment should be installed in

accordance with the National Fire Protection Association’s

(NFPA) Standard 72. See Figure 2.

A-8-1.2.1.C Are More Smoke Alarms Desirable?

The required number of smoke alarms might not provide

reliable early warning protection for those areas separated

by a door from the areas protected by the required smoke

alarms. For this reason, it is recommended that the

householder consider the use of additional smoke alarms

for those areas for increased protection. The additional

areas include the basement, bedrooms, dining

room, furnace room, utility room, and hallways not

protected by the required smoke alarms. The installation of

smoke alarms in kitchens, attics (finished or unfinished), or

garages is not normally recommended, as these locations

occasionally experience conditions that can result in

improper operation.

Important: Regulations pertaining to smoke alarm

installations vary from state to state. For more information,

contact your local fire department or local authority having

jurisdiction.

Summary of content (8 pages)

PAGE 1
868 MHz & 433 MHz Wireless Supervised Photoelectric Smoke Detectors Installation Instructions GENERAL DESCRIPTION The Smoke Detectors are battery-powered photoelectric smoke detectors with a built-in supervised wireless transmitter. When sufficient smoke is detected or the test feature is operated, the detector will sound its alarm horn and the transmitter will send an ALARM message. If the alarm condition remains, the message will be repeated 2 or more times (with 65 second intervals).
PAGE 2
In addition to NFPA 72, use the following location guidelines to optimize performance and reduce the chance of false alarms from the alarm: Locate ceiling-mounted smoke alarms in the center of a room or hallway at least 4 inches from any walls or partitions. • Locate wall-mounted smoke alarms so the top of the alarm is 4 to 12 inches below the ceiling. • Locate in a suitable environment as follows: − Temperature between 40ºF (4.4ºC) and 100ºF (37.
PAGE 3
Testing the Alarm Sensitivity The smoke alarm provides a sensitivity level test mode that allows you to check the smoke alarms sensitivity using the Test/Silence button and the LED indicator on the alarm as follows: 1. 2. Press the Test/Silence button on the smoke alarm for 2 seconds. Once the test starts, the alarm LED flashes one to nine times. Count the number of times the LED flashes and use the following table to determine the status of the smoke sensitivity and what action to take, if any.
PAGE 4
Replacing the Batteries Use only 3V lithium A batteries as listed on the battery compartment cover. Remove the alarm from the mounting base. See Attaching and Removing the Alarm. Slide the battery compartment cover away from the alarm to unsnap it and lift it off. See Figure 4. Remove the batteries and dispose of properly. Observing correct polarity, insert two new 3V lithium batteries into the battery compartment and replace the cover. Reattach the alarm to the mounting base.
PAGE 5
FIRE PREVENTION AND ESCAPE The purpose of an early warning smoke alarm is to detect the presence of fire in its early stages and sound an alarm giving the occupants time to exit the premises safely. Avoid Fire Hazards No detection device can protect life in all situations. Therefore, safeguards should be taken to avoid potentially dangerous situations as follows: Do not smoke in bed Do not leave children home alone Never clean with flammable liquids such as gasoline.
PAGE 6
ROKONET LIMITED WARRANTY CAUTION NOTICE Rokonet Electronics Ltd. and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 12 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller can not guarantee the performance of the security system which uses this product.
PAGE 7
PAGE 8
Specifications Voltage…………………………….…..2 X 3VDC Typical average standby current……………25µA Typical test current…………………………2mA Typical alarm current………………………70mA Battery life…………………………… 1year (min) Battery type…………...……………….3V lithium, ……………………...Duracell® DL123A, MN1500 …………………..Sanyo® and Panasonic® CR123A …………………………..Eveready® energizer E91 Low battery threshold…low battery signal at 2.70V Sounder…………………….85dB at 10 feet (3.3m) Low battery beep rate……...1 every 30 sec. + 2 sec. Sensitivity………………………………2.3%+0.