Install guide 8029B ROOM TEMP FAN OFF L COO O AUT ON T H EA ROOM TEMP FAN OFF L COO O AUT ON T H EA Customer Support: 888-515-2585 or Visit our website www.ritetemp-thermostats.
Install guide 8029B PG 1 Caution To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply before beginning work. This can be done at the circuit breaker, or at the appliance. Tools You will need #1 Phillips screwdriver (small) and Drill with 3/16-in. (4.8mm) bit for this installation. 1 Location On replacement installations, mount the new thermostat in place of the old one if possible.
2 Remove old unit IMPORTANT : LABEL ALL WIRES W Switch electricity to the furnace and BEFORE DISCONNECTING THEM! air conditioner OFF; then proceed with the following steps. Remove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the side or front. These must be loosened. Note the letters printed near the terminals. Attach labels (enclosed) to each wire for G B identification.
Before you Connect Wires Please follow these guidelines for safe and secure wire connections. Strip insulation 3/8 in. (9.5mm) from wire ends. Take care not to damage the labels for each wire in handling. Connect labeled wires only to a terminal with corresponding letter. Bend the wire slightly, insert the wire under the contact plate and tighten the screw down onto the wire. Caution D o n o t a l l ow w i r e s t o t o u c h e a c h o t h e r o r p a r t s o n t h e r m o s t a t .
When you have finished making connections. Hook the top of the body onto the base, swing the body C RC O B RH W Y G down, and snap the body onto the base. 5 Install Batteries TEM ROOM P FAN OFF COOL ON AUTO T HEA PG 7 The 8029B requires 2 AA batteries to operate your furnace and retain its programmed temperature in memory. Switch MODE switch to OFF and the FAN switch to AUTO. AA Remove the control unit from the wall unit.
Check Unit cont. NOTE: If you have an electric furnace system and the blower does not operate after installation, remove the thermostat, turn it over, and find the electric/gas heat selector jumper on the back of the control unit. Switch it to "Elect"(see Diag below). Congratulations, you have successfully installed your unit. Please proceed to the OPERATING Guide to initialize the new thermostat. 7 Power Options 1) The 8029B can run on batteries only.
ace From Furn C R or STEP 1 - Connect the R (or RH) wire to RH the RH terminal on the thermostat. This connects the Heater Power to the W thermostat. 2 WIRE Heating (GAS MILLIVOLT or 24vac STEP 2 - Connect the W wire to the W terminal on the thermostat. This connects the heater control line to the thermostat. Your Heater is now connected to the thermostat. Thermostat jumper wire C R W HEAT Power HEAT FURNACE NOTE: Wires marked with the dotted line are optional.
ace From Furn it and AC un STEP 1 - Connect the Y wire to the Y terminal on the thermostat. This RH connects to the Cooler compressor. or STEP 2 - Connect the RH or R wire R to the RH terminal on the thermostat. G This connects the Heater/Cooler C W Power. STEP 3 - Connect the W wire to the W terminal on the thermostat. This connects to the heater control line. STEP 4 - Connect the G wire to the G terminal on the Thermostat. This connects to the Fan. Your HVAC system is now connected to the thermostat.
STEP 1 - Connect the G wire to the G terminal on the thermostat. Y This connects the Fan. O STEP 2 - Add a jumper wire between or B W and Y. STEP 3 - Connect the Y wire to the Y R C terminal on the thermostat. This connects the Compressor. STEP 4 - Connect the O or B wire to the O or B terminal on the thermostat. (If you have both O and B contact Ritetemp or your local HVAC contractor for further help) This connects the change over valve. STEP 5 - Connect the R wire to the RC terminal.
