Owner`s manual

qtm9322b.pm5
For assistance, call RITRON at 800-USA-1-USA (800-872-1872) or visit us at www.ritron.com
C. TO PROGRAM THE ASSISTANCE NEEDED MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial 312. Quick Assist responds with three short tones
to prompt you to begin speaking, then records the
message. This message is to be no longer than 8
seconds. Remember: speak loudly and clearly.
EXAMPLE: Customer needs assistance in Aisle 9.
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional
features, or you may dial 999 and hang up the tele-
phone to stop programming.
NOTE: To review your recorded message,
dial "412".
D. TO PROGRAM TIME BETWEEN REPEATED MESSAGES:
(DEFAULT SETTING IS 30 SECONDS)
1. Look up the code for the desired time between mes-
sages on Table 4, below.
2. Pick up the telephone receiver and listen for the acknowl-
edge tone.
3. Dial 512, then the code digit from Table 4.
EXAMPLE: If you select 2 minutes as the time between
messages, dial 5124.
4. Quick Assist responds with a single beep to indicate it
has programmed the time between messages.
5. You may either continue programming additional
features, or you may dial 999 and hang up the tele-
phone to stop programming.
! ! ! IMPORTANT ! ! !
If your Quick Assist unit fails to operate
correctly, or is programmed incorrectly, put
the unit into default Quick Assist mode using
the following procedure:
1. Pick up the telephone receiver and listen for the
acknowledge tone.
2. Dial the correct option (A or B below), to restore
factory defaults; a short beep indicates successful
completion.
A. For RQT-150-PB, dial 978.
B. For RQT-450-PB, dial 979.
3. Dial 814 to put the unit into Quick Assist mode; a
short beep indicates successful completion.
4. Program Sections A through F, above. Section G is
optional.
5. Programming of the Ritron Quick Assist is complete!
E. TO PROGRAM THE ASSISTANCE IS NO
LONGER NEEDED MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial 311. Quick Assist responds with three short tones
to prompt you to begin speaking, then records the
message. This message is to be no longer than 8
seconds.
EXAMPLE: Aisle 9 OK.
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional
features, or you may dial 999 and hang up the tele-
phone to stop programming.
NOTE: To review your recorded message,
press "41
F. TO PROGRAM THE "LOW BATTERY" MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial "35". Quick Assist responds with three short tones to
prompt you to begin speaking, then records the message.
This message is to be no longer than 1.5 seconds.
EXAMPLE: "Low battery Aisle 9"
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional features,
or you may dial 999 and hang up the telephone to stop
programming.
NOTE: To review your recorded message,
dial "45".
G. TO PROGRAM THE "ASSISTANCE NEEDED" MESSAGE
REPEAT LIMIT: (DEFAULT SETTING IS 8 TIMES)
1. Look up the code for the desired number of message
repeats on Table 5, below.
2. Pick up the telephone receiver and listen for the acknowl-
edge tone.
3. Dial "612", then the code digit from Table 5.
EXAMPLE: If you select 3 times as the message repeat limit,
dial 6123.
4. Quick Assist responds with a single beep to indicate it has
programmed the message repeat limit.
5. Dial 999 and hang up the telephone to stop program-
ming.
TABLE 5:
MESSAGE
REPEAT LIMIT CODE NUMBER
1 time ...................................................... 1
2 times ..................................................... 2
3 times ..................................................... 3
4 times ..................................................... 4
5 times ..................................................... 5
6 times ..................................................... 6
7 times ..................................................... 7
8 times ..................................................... 8
Repeat forever; no limit ............................. 9
 DEFAULT
(Programming Instructions continued from page 2)
 4 
TABLE 4:
TIME BETWEEN
MESSAGES CODE NUMBER
No Message ............................................. 0
On Changes Only ..................................... 1
30 seconds .............................................. 2
1 minute ................................................... 3
2 minutes ................................................. 4
5 minutes ................................................. 5
10 minutes ............................................... 6
30 minutes ............................................... 7
1 hour ...................................................... 8
2 hours .................................................... 9
 DEFAULT