Operating instructions
Table Of Contents
- Doku_Standard_Wasser-RK_GB_V09.pdf
- General description
- Important safety measures
- Transport and handling
- Installation
- Electrical connection
- Start-up
- Hydrological data
- Maintenance
- Shutting down / disposing the cooling system
- General fault analysis
- Evaporator pressure
- Compressor is continuously being switched on and off
- No medium circulation
- Appendix
- Datenblatt_060535.pdf
- PID.pdf
- Schaltplan_englisch.pdf
- MPRA-SMK-A-0-Englisch.pdf
- BA_PMA-KS40-1_41-1_42-1_englisch.pdf
- Contents
- 1 Mounting 5
- 2 Electrical connections 6
- 3 Operation 10
- 4 Configuration level 21
- 4.1 Configuration survey 21
- 4.2 Configuration 22
- 4.3 Set-point processing 29
- 4.4 Configuration examples 30
- 4.4.1 On-Off controller / Signaller (inverse) 30
- 4.4.2 2-point controller (inverse) 31
- 4.4.3 3-point controller (relay & relay) 32
- 4.4.4 3-point stepping controller (relay & relay) 33
- 4.4.5 Continuous controller (inverse) 34
- 4.4.6 D - Y - Off controller / 2-point controller with pre-contact 35
- 4.4.7 KS4x-1 with measured value output 36
- 5 Parameter setting level 37
- 6 Calibration level 41
- 7 Programmer 44
- 8 Timer 46
- 9 BlueControl 49
- 10 Versions 50
- 11 Technical data 51
- 12 Safety hints 55
- Index
- Contents
- Parameterliste PMA_english.pdf
- BA_Strömungswächter_SI1000_englisch.pdf
- BA-IFM_Drucksensor PN7009_englisch.pdf
- Endress-Hauser-Display BA188Ra3_englisch.pdf
- Endress-Hauser-Messsonde_BA_englisch.pdf
- BA_FEC12_englisch.pdf
Simulation for level Enter the level value to be simulated. The appropriate current is given by the
electronic insert.
Step Entry Cursor in Display at Significance
1 3
SERVICE/SIMULATION
Service/Simulation
26
SIM. LEVEL
Simulation for level
e.g. 77.06
Actual measured value is displayed
3 e.g. 35.00
35.00
Level to be simulated is entered
4 F4
[ENTER]
Confirms entry, value to be transmitted
Simulation for volume Enter the volume value to be simulated. The appropriate current is given by the
electronic insert.
Step Entry Cursor in Display to Significance
1 3
SERVICE/SIMULATION
Service/Simulation
27
SIM. VOLUME
Simulation of volume
e.g. 77.06
Actual measured value is displayed
3 e.g. 5.00
5.00
Volume to be simulated is entered
4 F4
[ENTER]
Confirms entry, value to be transmitted
Simulation for current Enter directly the current value to be simulated.
Step Entry Cursor in Display at Significance
1 3
SERVICE/SIMULATION
Service/Simulation
27
SIM. CURRENT
Simulation of current output
e.g. 17.02
Actual measured value is displayed
3 e.g. 8.00
8.00
Current to be simulated is entered
4 F4
[ENTER]
Confirms entry, value to be transmitted
Note!
The values entered during simulation are stored until simulation is again switched off.
Note!
6 Diagnosis and Troubleshooting Electronic insert FEC 12 (HART)
16
Endress+Hauser