MODEL NO.: QCF-DB52061 Installation Guide READ AND SAVE THESE INSTRUCTIONS MODEL NO.: QCF-DB52061 Table of Contents: Safety tips Pg.2 Unpacking your fan Pg.3 Parts included Pg.3 Tools and material required Pg.4 Outlet Box Pg.5 Hanging Bracket Installation Pg.4 - 5 Bulb installation Pg.6 Fan Assembly Pg.6 - 7 Wiring Pg.7 - 8 Blade Assembly Pg.9 Canopy Assembly Pg.9 Light Kit and Shade Assembly Pg.10 Testing Your Fan Pg.11 Trouble Shooting Pg.11-12 Maintenance Pg.
MODEL NO.: QCF-DB52061 SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
MODEL NO.: QCF-DB52061 1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or styrofoam to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory.
MODEL NO.: QCF-DB52061 3. Tools Required Step ladder Pliers Screw driver flat head and phillip Electrical tape Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft.(2.13m) from the floor and 30in.(76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling.
MODEL NO.: QCF-DB52061 CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.
MODEL NO.: QCF-DB52061 6. Bulbs Installation. Installing bulbs in the Motor Housing, locate the four access plates on the motor housing top. Remove two screws per access plate to reach each socket, use phillip screwdriver. Do not remove the Center Screw on each Access Plate Install each candelabra base Type C, 7W bulbs (Not Included). Reattach the Access Plates ensuring the screws are tightened enough to avoid vibrations during the fan operation.
MODEL NO.: QCF-DB52061 8. Fan Assembly with Down Rod - Choose the 4” or 21” Down Rod Remove Pin and Clip from down rod (if you have not already done so). Slide the Down rod through the canopy, and the Down rod cover as shown. Thread the electrical wires through down rod and pull extra wire slack from the upper end of the down rod. Tip: Apply small piece of electrical tape to the ends of the electrical wires to keep them together when threading them through the down rod. Loosen the Yoke set screw.
MODEL NO.: QCF-DB52061 3. Install the receiver into the Hanging bracket of the fan. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. Do not install in damp locations or immerse in water. For indoor use only. Do not pull on or cut the receiver wire leads shorter. 7. Proceed making the wire connections following this diagram carefully. CAUTION: Incorrect wire connection would damage the receiver.
MODEL NO.: QCF-DB52061 Important: Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring, or if the house/building wires are different colors than those referred to in the instructions, please use a qualified electrician. 10. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades.
MODEL NO.: QCF-DB52061 11. Light Kit Assembly. 1. Remove the three screws from the Light kit. 2. Plug the connectors from the Light kit to the connectors from the Switch housing. Please note the correct wiring is: White to White Blue to Blue 3. Gently push the connectors into switch housing and align the holes in the Light kit with holes in the Switch housing. Secure the light kit with the 3 screws that were previously removed.
MODEL NO.: QCF-DB52061 12. Testing Your Fan. It is recommended that you test the fan before finalizing installation. Restore power from circuit box and light switch (if applicable). Test the fan speeds from the Remote controller. Start at the OFF position (no blade movement) and continue testing the LOW, MED and HI speeds. Every time you press any key the red LED witness light will turn ON at the top of the controller.
MODEL NO.: QCF-DB52061 FAN FOUND NOISY 1. Always take a few days" break in" time for any new fan at medium or high speed. Try to diagnose the exact location of the noise by listening carefully from several sides (blades, motor, light kit, etc). Fan noise can come from a light kit 2. Make sure all screws in the fan assembly and light kit are tight and properly threaded. If not, back out and re tighten.