Instructions / Assembly

ManualsBrandsRiver of Goods ManualsCeiling FansDuchess 52 in. Clear Crystal LED Ceiling Fan With Light

MODEL NO.: 20060

Installation Guide

MODEL NO.: 20060

You may install your ceiling fan as a flush mount, or you may use the provided down rod(s). Measure your

room height before installing the fan and consider the different installation height options indicated in the

above diagram.

Table of Contents:

Safety tips Pg.2 Wiring Pg.7-8

Unpacking your fan Pg.3 Canopy Assembly Pg.8

Tools and material required Pg.4 Blade Assembly Pg.8-9

Outlet Box Pg.4-5 Light Kit and Shade Assembly Pg.9-10

Hanging Bracket Installation Pg.4 -

Changing Bulbs (Flush Mount) Pg.10

Fan Assembly (Flush Mount) Pg.6 Troubleshooting & Maintenance Pg. 11

Fan Assembly (w/Down Rod) Pg.

Professional Installation Recommended

Note: Approximate Time of Assembly: 30 Minutes to 1 Hour

PRINTED IN CHINA

READ AND SAVE THESE

INSTRUCTIONS

Summary of content (11 pages)

PAGE 1
MODEL NO.: 20060 Installation Guide READ AND SAVE THESE INSTRUCTIONS MODEL NO.: 20060 You may install your ceiling fan as a flush mount, or you may use the provided down rod(s). Measure your room height before installing the fan and consider the different installation height options indicated in the above diagram. Table of Contents: Safety tips Pg.2 Unpacking your fan Pg.3 Wiring Pg.7-8 Canopy Assembly Pg.8 Tools and material required Pg.4 Outlet Box Pg.4-5 Blade Assembly Pg.
PAGE 2
MODEL NO.: 20060 SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 1.
PAGE 3
MODEL NO.: 20060 1. Unpacking Your Fan Carefully open the packaging. Remove items from styrofoam inserts. Remove motor housing and place on a soft, dry surface to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned. Check against parts inventory (listed below) that all parts have been included. 2.
PAGE 4
MODEL NO.: 20060 3. Tools Required • • • • • Step ladder Pliers Screwdriver (flat head and phillips) Electrical tape Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft (2.13m) from the floor and 30 in (76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2 square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling.
PAGE 5
MODEL NO.: 20060 CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove the hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.
PAGE 6
MODEL NO.: 20060 6. Bulb Installation 1. Locate the four (4) access plates on the motor housing 2. On each access plate, remove the outer two (2) screws using a phillips screwdriver and set aside 3. Install the provided bulbs 4. Reattach the access plates(s) with the removed screws, ensuring that each screw is securely fastened CAUTION - Refer to the Maximum Wattage Caution Label located near the lamp holder for recommended maximum wattage-do not exceed recommended wattage.
PAGE 7
MODEL NO.: 20060 8. Assembly with Down Rod 1. Remove pin and clip from down rod. Slide the down rod through the canopy and the down rod cover as shown in figure 2. Thread the electrical wires through the down rod and pull the extra wire slack through the down rod Tip: Apply a small piece of electrical tape to the ends of the electrical wires to keep them together when threading them through the down rod 3. Loosen the yoke set screw.
PAGE 8
MODEL NO.: 20060 to the ground wire located on the down rod end. The splices, after being carefully made, should be turned upward and pushed carefully up into the outlet box. Note: Wrap each wire nut separately with electrical tape as an extra safety measure. Important: Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
PAGE 9
MODEL NO.: 20060 6. Remove motor shipping pads, discard pads and save the screws 7. Align the blade arm holes with the motor housing holes and attach the two (2) screws/washers. Fasten securely 8. Repeat Step 7 for the remaining blade arms 11. Light Kit Assembly 1. Remove the three (3) screws from the light kit and set aside 2. Plug the connector from the light kit into the connectors from the switch housing 3. Correct wiring o White to White o Blue to Blue 4.
PAGE 10
MODEL NO.: 20060 Tiered Shade Installation (if applicable) 1. Remove the three (3) screws from Shade A and set aside 2. Thread the pull chains through the designated holes in Shade B 3. Align the three (3) holes from Shade B with the holes in Shade A and insert the three (3) removed screws Changing Bulbs (Flush Mount) Need to change your motor housing bulbs? No worries! Follow the steps below to guide you through the bulb changing process, all while keeping your ceiling fan mounted 1.
PAGE 11
MODEL NO.: 20060 Ceiling Fan Troubleshooting Guide Welcome to the River of Goods family! We’re honored you’ve decided to include one of our ceiling fans in your home. Problem Fan/Lights do not start Fan is noisy Fan does not move much air Fan shakes or wobbles Solution • Check all fuses/circuit breakers • Turn off electrical power and ensure the wiring is correct • Ensure bulbs(s) are fully installed in the socket • Allow a 24-hour “break in” period.