Instructions / Assembly

ManualsBrandsRiver of Goods ManualsCeiling FansPrairie 52 in. LED Oil Rubbed Bronze Caged Ceiling Fan With Light

MODEL NO.: 20074

Installation Guide

MODEL NO.: 20074

You may install your ceiling fan as a flush mount, or you may use the provided down rod(s). Measure your

room height before installing the fan and consider the different installation height options indicated in the

above diagram.

Table of Contents:

Safety tips Pg.2 Wiring Pg.7

Unpacking your fan Pg.3 Canopy Assembly Pg.8

Tools and material required Pg.4 Blade Assembly Pg.8

Outlet Box Pg.4-5 Light Kit and Shade Assembly Pg.9

Hanging Bracket Installation Pg.4 -

Troubleshooting & Maintenance Pg.10

Fan Assembly (Flush Mount) Pg.6

Fan Assembly (w/Down Rod) Pg.

Professional Installation Recommended

Note: Approximate Time of Assembly: 30 Minutes to 1 Hour

PRINTED IN CHINA

READ AND SAVE THESE

INSTRUCTIONS

Summary of content (10 pages)

PAGE 1
MODEL NO.: 20074 Installation Guide READ AND SAVE THESE INSTRUCTIONS MODEL NO.: 20074 You may install your ceiling fan as a flush mount, or you may use the provided down rod(s). Measure your room height before installing the fan and consider the different installation height options indicated in the above diagram. Table of Contents: Safety tips Pg.2 Unpacking your fan Pg.3 Wiring Pg.7 Canopy Assembly Pg.8 Tools and material required Pg.4 Outlet Box Pg.4-5 Blade Assembly Pg.
PAGE 2
MODEL NO.: 20074 SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 1.
PAGE 3
MODEL NO.: 20074 1. Unpacking Your Fan Carefully open the packaging. Remove items from styrofoam inserts. Remove motor housing and place on a soft, dry surface to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned. Check against parts inventory (listed below) that all parts have been included. 2.
PAGE 4
MODEL NO.: 20074 3. Tools Required • • • • • Step ladder Pliers Screwdriver (flat head and phillips) Electrical tape Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft (2.13m) from the floor and 30 in (76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2 square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling.
PAGE 5
MODEL NO.: 20074 CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove the hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.
PAGE 6
MODEL NO.: 20074 6. Flush Mount Assembly NOTE: If assembling with down rod, proceed to Step 7 1. 2. 3. 4. 5. Remove round rubber ring from canopy Thread the electrical wires through the canopy Remove every other screw on the motor housing (3 screws total) WARNING – Ensure you only remove every other screw, others must remain firmly tightened. Attach the canopy to the motor housing securely with the three (3) removed screws. Tighten firmly. Continue to Step 8 for wiring 7. Assembly with Down Rod 1.
PAGE 7
MODEL NO.: 20074 8. Ceiling Fan Wiring WARNING: Failure to disconnect power supply prior to the installation may result in serious injury and fire hazard Important: Be sure outlet box is properly grounded or that a ground wire (GREEN or bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
PAGE 8
MODEL NO.: 20074 9. Canopy Assembly 1. Loosen the four (4) screws/washers on the side of the hanging bracket 2. Lift canopy to the hanging bracket, and secure the canopy with the four (4) screws/washers. Securely tighten screws 10. Blade Assembly 1. Locate fifteen (15) screws/washers in the hardware pack 2. Hold blade arm up to blade and align the three (3) holes 3. Insert three (3) screws/washers with fingers, and tighten with a phillips screwdriver 4.
PAGE 9
MODEL NO.: 20074 11. Light Kit Assembly 1. Remove the three (3) screws from the light kit and set aside 2. Plug the connector from the light kit into the connectors from the switch housing 3. Correct wiring o White to White o Black to Blue 4. Gently push the connectors into the switch housing and align the holes in the light kit with the holes in the switch housing. Secure the light kit with the three (3) removed screws 5.
PAGE 10
MODEL NO.: 20074 Ceiling Fan Troubleshooting Guide Welcome to the River of Goods family! We’re honored you’ve decided to include one of our ceiling fans in your home. Problem Fan/Lights do not start Fan is noisy Fan does not move much air Fan shakes or wobbles Solution • Check all fuses/circuit breakers • Turn off electrical power and ensure the wiring is correct • Ensure bulbs(s) are fully installed in the socket • Allow a 24-hour “break in” period.