ASSEMBLY INSTRUCTIONS RiverRidge® X-Frame Bath Spacesaver ITEM #: 06-003 White ITEM #: 06-004 Espresso ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over.
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT, THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 1PC Top Board 2 2PCS Upper Side Frame 3 1PC Bottom Board 4 1PC Shelf 5 1PC Lower Left Side Frame 6 1PC Upper Rear Cross Bar 7 3PCS Cross Bar 8 1PC Lower Rear Cross Bar 9 1PC Lower Right Side Frame
PARTS LIST NO PARTS QTY DESCRIPTION A 18PCS Screw (5x45mm) B 12PCS Screw (4x35mm) C 2PCS Plastic Anchor D 2PCS Screw (4x60mm) E 14PCS Plastic Cap F 1PC Allen Wrench G 4PCS Wood Dowel TOOLS NEEDED FOR ASSEMBLY: PHILIPS SCREWDRIVER (NOT INCLUDED) THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED To order replacement parts at no cost to you, email customer.service@ssi-rr.
STEP 1 1. 2. 3. 4. 5. Place top board (1) and bottom board (3) upside down on a soft padded surface. Attach upper rear cross bar (6) to top board (1) by inserting 3 screws (B) through holes on upper rear cross bar (6) and tighten to top board (1). Repeat step above to assemble 1 cross bar (7) to top board (1). Attach 1 cross bar (7) to bottom board (3) by inserting 3 screws (B) through holes on cross bar (7) and tighten to bottom board (3).
STEP 3 1. Repeat Step 2 to assemble other upper side frame (2). STEP 4 1. Attach bottom board (3) to bottom side of 2 upper side frames (2) by inserting 4 screws (A) through holes on bottom board (3), then tighten to 2 upper side frames (2) with Allen wrench (F).
STEP 5 1. 2. 3. Insert 4 wooden dowels (G) into holes on lower rear cross bar (8). Attach 1 lower left side frame (5) to bottom board (3) and lower rear cross bar (8) by inserting wooden dowels (G) into holes on lower left side frame (5) and inserting 3 screws (A) through holes on lower left side frame (5), then tighten to 2 cross bars (7) on bottom board (3) and lower rear cross bar (8) with Allen wrench (F).
STEP 7 Option #1: Securing to Drywall 1. Position shelf against wall in desired location. Using a pencil, make 2 small marks on wall through holes on inside of shelf. Move shelf away from wall and screw 2 plastic anchors (C) into wall on pencil marks. 2. Place shelf against wall, insert 2 screws (D) through holes on inside of shelf, then tighten to plastic anchors (C). Option #2: Securing to Drywall and Wood Stud 1. Position shelf against wall in desired location.
Enjoy your new RiverRidge® Spacesaver! Thank you for purchasing this RiverRidge® Home item. We hope you enjoy it and consider purchasing other RiverRidge® items. To order replacement parts at no cost to you, email customer.service@ssi-rr.com, call 1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States. If purchased outside of the United States, please contact retailer where purchased. RiverRidge® is a registered trademark of Sourcing Solutions, Inc.