ASSEMBLY INSTRUCTIONS RiverRidge® Ellsworth Tall Corner Cabinet ITEM # 06-027 XS WHITE ITEM # 06-028 XS ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of the small parts. Care should be taken in unpacking and assembling this item to keep the small parts away from children. WARNING Young children can be seriously injured or killed, if furniture tips over. Don’t use this item for a TV stand. Use angle-braces or anchors to secure furniture to the wall.
Send requests for missing or damaged parts replacements by email to : customer.service@ssi-rr.com or call toll free 1-(844)-223-5201 or order parts on line at www.riverridgehome.com THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO PARTS QTY DESCRIPTION A 4PC CAM BOLT B 4PC CAM LOCK C 24PC WOOD DOWEL D 1PC MAGNET E 2PC SCREW 3x14mm F 18PC WOOD SCREW 3x10mm G 4PC HINGE H 2PC MAGNET PLATE I 30PC WOOD SCREW 4x25mm J 2PC KNOB K 2PC MACHINE SCREW 4x20mm L 4PC ADJUSTABLE SHELF HOLDER M 4PC LONG WOOD SCREW 4x35mm N 2PC LONG WOOD DOWEL O 4PC PLASTIC ANCHOR P 4PC LONG SCREW 4x40mm
NO PARTS QTY DESCRIPTION 1 1PC MIDDLE CONNECTION BOARD 2 1PC LFET LOWER SUPPORT BOARD 3 1PC RIGHT LOWER SUPPORT BOARD 4 1PC LOWER CROSS BAR 5 1PC RIGHT SIDE DOOR 6 1PC LEFT SIDE DOOR 7 1PC ADJUSTABLE SHELF 8 2PC TOP & BOTTOM FIXED SHELF 9 1PC LEFT LOWER SIDE PANEL 10 1PC RIGHT LOWER SIDE PANEL 11 1PC RIGHT UPPER SUPPORT BAR 12 1PC LEFT UPPER SUPPORT BAR 13 1PC 14 1PC LEFT UPPER SIDE PANEL 15 1PC RIGHT UPPER SIDE PANEL 16 2PC TOP OPEN SHELF TOP CROSS BOARD
STEP 1 1. Insert 1 Wood screw(F) through hole in the Magnet plate(H) then tighten to Right side door(5) by using a Philips screwdriver. 2. Insert 4 Wood screws(F) through holes in 2 hinges(G) then tighten to the Right side door(5) by using a Philips screwdriver. 3. Repeat the above steps to assemble the Magnet plate(H) and 2 Hinges(G) to Left side door(6). STEP 2 1. Place lower cross bars (2) and (3) as pictured above with backside of each part facing towards you. 2.
STEP 3 1. Place the Right side door(5) and Left side door(6) to the Left lower support board(2) and Right lower support board(3) in position as shown in diagram above. Door panels will have the backside facing you. 2. Insert 4 Wood screws(F) through holes in the Hinge(G) on the Left side door(6) then tighten to Left lower support board(2) by using a Philips screwdriver. 3.
STEP 5 1. Place the Left lower side panel(9) as shown above to prepare to attach to the Shelf(8) and Left lower support board(2). 2. Insert the Wooden dowei(C) into the dowel hole in the Left lower side panel(9). 3. Insert 4pc Wood screw(I) through the holes in the Left lower side panel(9) then tighten to the Shelf(8) and Left lower support board(2) using a Philips head screwdriver. STEP 6 1.
STEP 7 1. Screw 4 Cam bolts(A) into the pre-threaded holes of the Middle connection board(1) by hand. Do not over tighten. 2. Attach the Magnet(D) to the Middle connection board(1) by inserting 2pc Screw(E) through the holes on the Magnet(D) then tighten to the Top board(1). STEP 8 1. Place lower cross bars (11) and (12) as pictured above with backside of each part facing towards you. 2. Insert 4 wood dowels(C) into the dowel holes in the end of the Top cross board(13). 3.
STEP 9 1. Place Shelf(8) in position as shown above to prepare to attach to both upper support boards(11),(12). 2. Insert 2 screws (I) through holes in the shelf (8) then tighten to the Left upper support board(12) and Right upper support board(11) by using a Philips screwdriver. 3. Insert 2 wood dowels(C) into the dowel holes on the Shelf(8). STEP 10 1. Insert 2pc of the wood dowels(C) into the dowel holes in the two Shelf(16) parts. 2.
STEP 11 1. Place the Left upper side panel(14) in position as shown above to prepare to attach to Shelves (16), the Left upper support board(12) and Shelf(8). 2. Insert the Wood dowels(C) into the dowel holes in inner side of the Left upper side panel(14). 3. Insert 4pc Wood screws(I) through the holes on the Left upper side panel(14) then tighten to the Shelf(8) and Left upper support board(12) using a Philips head screwdriver. STEP 12 1. Insert 2 wood dowels(C) into the dowel holes on the Shelves(16).
STEP 13 1. Place the Right upper side panel(15) in position as shown above to prepare to attach to and to left upper side panel(14), shelves (16) and shelf(8). 2. Insert the Wood dowels(C) that are in shelves(16) and shelf(8) into the dowel holes in inner side of the Right upper side panel(15). 3. Insert 9pc Wood screw(I) through the holes on the Right upper side panel(15) then tighten to the Shelf(8), shelves(16), Right upper support board(11) and Left upper side panel(14).
STEP 15 1. Insert 2pc Long wood dowels(N) and 4pc wood dowels(C) into the dowel holes on the Lower support board (2), (3) and lower side panel(9),(10). 2. Two people may be required for this step. Attach the upper unit to lower unit by inserting the wooden dowel(C),(N) into the dowel holes on the Upper support board(11),(12) and lower side panel(14),(15). Also insert the 4 Cam bolts(A) into the Cam lock holes of lower side panels (14)(15).
STEP 16 1. Insert 4pc Cam locks(B) into the cam lock holes on the Left lower side panel(9) and Right lower side panel(10). Rotate the Cam locks(B) clockwise to lock the cam bolts in place using a flat head screwdriver. 2. Insert 4pc adjustable shelf holders(L) into the holes on the Left lower side panel(9) and Right lower side panel(10). 3. Insert 1pc Machine screw(K) through the hole on the Left door(6) then tighten to the Knob(J) 4. Repeat above step to assemble another knob on the Right door(5).
STEP 17 1. With a nail or screw mark the 4 holes on the wall that will be used to attach the plastic wall anchors(O) and anchor screws(P). 2. Drill the holes on the wall where you have marked the 4 spots in step 1 above. 3. Insert 4pc Plastic wall anchor(O) into the holes on the wall using your hand or small hammer. 4. Insert 4pc Long screw(P) through the holes on the Lower and upper side panels, then tighten to the Plastic wall anchor(O). 5. Put the Shelf(7) onto the Plastic holders(L).
ENJOY YOUR NEW RiverRidge® CABINET NOW ! Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct the hazard such as tightening of screws and taking any damaged parts away from the children. Thank you for purchasing this RiverRidge® Home Products item. We hope you enjoy it, and consider purchasing other RiverRidge® items. Send requests for missing or damaged parts replacements by email to : customer.service@ssi-rr.