ASSEMBLY INSTRUCTIONS RiverRidge® Ashland Tall Cabinet ITEM# 06-082 ITEM# 06-083 White Gray ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over. Don’t use this item for a TV stand or place heavy objects on top of item.
THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF AND 10 POUNDS PER DRAWER OR A TOTAL OF 160 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR THE DRAWER WITH MORE THAN 10 POUNDS. OVERLOADING THE CABINET MAY CAUSE DAMAGE TO THE CABINET OR CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 1PC Top board 2 1PC Lower left side panel 3 1PC Lower right side panel 4 1PC Lower back panel 5 1PC Upper cross bar 6 1PC Shelf 7 1PC Bottom board 8 1PC Decorative panel 9 1PC Door 10 1PC Drawer back board 11 2PCS Drawer side panel 12 1PC Drawer bottom board 13 1PC Drawer front board 14 1PC Upper left side panel 15 1PC Upper right side panel 16 2PCS Open shelf 17 1PC Upper back panel 18 1PC Middle connection board
NO QTY DESCRIPTION A B C D E F G H 18PCS Cam bolt 18PCS Cam Lock 26PCS Wood dowel 14PCS Wood Screw 3x10mm 2PCS Drawer holder 8PCS Screw 3.5x25mm 24PCS Back Board Screw 2.5x12mm 2PCS Drawer plastic stopper I 2PCS Metal hinge J K L 1PC Knob 1PC Machine Screw 4x20mm 1PC Magnet plate M N O P Q R S T 1PC Magnet 2PCS Screw 3x14mm 4PCS Plastic shelf holder 2PCS Bracket 1PC Screw 2.
STEP 1 1. Screw 2 cam bolts (A) in pre-threaded holes on upper left side panel (14). 2. Screw 2 cam bolts (A) in pre-threaded holes on upper right side panel (15). STEP 2 1. Insert 8 wood dowels (C) into wood dowel holes on upper left side panel (14) and upper right side panel (15). 2. Attach upper right side panel (15) to open shelf (16) by inserting cam bolts (A) into cam lock holes on end of open shelf (16) and inserting wood dowels (C) into wood dowel holes on open shelf (16). 3.
STEP 3 1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1). 2. Insert 4 wood dowels (C) into wood dowel holes on top board (1). 3. Attach top board (1) to upper left side panel (14) and upper right side panel (15) by inserting cam bolts (A) into cam lock holes and inserting wood dowels (C) into wood dowel holes on end of upper left side panel (14) and upper right side panel (15). 4.
STEP 5 1. Screw 3 cam bolts (A) into pre-threaded holes on lower left side panel (2). 2. Attach drawer holder (E) to lower left side panel (2) by inserting 2 wood screws (D) through holes on drawer holder (E) then tighten to lower left side panel (2). 3. Attach magnet (M) to lower left side panel (2) by inserting 2 screws (N) through holes on magnet (M) then tighten to lower left side panel (2). 4. Screw 3 cam bolts (A) into pre-threaded holes on lower right side panel (3). 5.
STEP 7 1. Insert 4 wood dowels (C) into wood dowel holes on middle connection board (18). 2. Attach upper pre-assembled unit to lower pre-assembled unit by inserting wood dowels (C) into wood dowel holes and inserting cam bolts (A) into cam lock holes on end of lower side panels (2) and (3). 3. Insert 4 cam locks (B) into cam lock holes on lower side panels (2) and (3), rotate clockwise to secure cam bolts (A) in place. STEP 8 1.
STEP 9 1. Attach 1 drawer side panel (11) to drawer back board (10) by inserting 2 screws (F) through holes on drawer side panel (11) then tighten to drawer back board (10). 2. Repeat above step to assemble another drawer side panel (11) to drawer back board (10). 3. Slide drawer bottom board (12) into grooves on both drawer side panels (11). 4.
STEP 10 1. Attach magnet plate (L) to door (9) by inserting 2 wood screws (D) through holes on magnet plate (L) then tighten to door (9). 2. Attach 2 metal hinges (I) to door (9) by inserting 4 wood screws (D) through holes on metal hinges (I) then tighten to door (9). 3. Attach knob (J) to door (9) by inserting 1 machine screw (K) through hole on door (9) then tighten to knob (J). 4.
STEP 11 1. Attach 1 metal bracket (P) to back of cabinet by inserting 1 screw (Q) through hole on metal bracket (P) then tighten to back of cabinet. 2. Use the position of the metal bracket (P) on cabinet to determine position of second metal bracket (P) on wall. Drill hole in wall where second metal bracket (P) will be placed. 3.
Enjoy your new RiverRidge® Cabinet! Thank you for purchasing this RiverRidge® Home item. We hope you enjoy it and consider purchasing other RiverRidge® items. To order replacement parts at no cost to you, email customer.service@ssi-rr.com, call 1-(844)-223-5201 or order parts online at www.riverridgehome.com RiverRidge® is a registered trademark of Sourcing Solutions, Inc.
INSTRUCCIONES PARA EL ARMADO ARMARIO ALTO ASHLAND DE RiverRidge® ARTÍCULO N.° 06-082 BLANCO ARTÍCULO N.° 06-083 GRIS REQUIERE QUE LO ARME UN ADULTO Este producto requiere que lo arme un adulto debido a las piezas pequeñas. Se debe tener cuidado al desempaquetar y armar este artículo para que las piezas pequeñas estén lejos de los niños. ADVERTENCIA Los niños pequeños pueden sufrir lesiones serias o incluso la muerte, si el mueble se tumba. No use este producto como mesa para un televisor.
ESTE ARMARIO ACEPTARÁ HASTA 25 LIBRAS POR ESTANTE Y 10 LIBRAS POR CAJÓN O SEA UN TOTAL DE 160 LIBRAS. NO CARGUE CADA ESTANTE CON MÁS DE 25 LIBRAS O EL CAJÓN CON MÁS DE 10 LIBRAS. CARGAR EXCESIVAMENTE EL ARMARIO PODRÍA CAUSAR DAÑO AL ARMARIO O CAUSAR SERIAS LESIONES O LA MUERTE. ADVERTENCIA SERIAS LESIONES O FATALES PUEDEN OCURRIR SI SE TUMBA EL MUEBLE.
LISTA DE PIEZAS N.° 1 CANT .
N.° PIEZAS CANT. DESCRIPCIÓN A 18 PIEZAS PERNO DE LEVA B 18 PIEZAS TRABA DE LEVA C 26 PIEZAS CLAVIJA DE MADERA D 14 PIEZAS TORNILLO PARA MADERA 3 x 10 mm E F 2 PIEZAS SOPORTE DEL CAJÓN G 24 PIEZAS TORNILLO DE LA TABLA TRASERA 2.
PASO 1 1. Atornille 2 pernos de leva (A) en los agujeros con rosca en el panel del lado izquierdo de arriba (14). 2. Atornille 2 pernos de leva (A) en los agujeros con rosca en el panel del lado derecho de arriba (15). PASO 2 1. Inserte 8 clavijas de madera (C) en los agujeros de las clavijas de madera del panel del lado izquierdo de arriba (14) y panel del lado derecho de arriba (15). 2.
PASO 3 1. Atornille 4 pernos de leva (A) en los agujeros con rosca en la tabla de arriba (1). 2. Inserte 4 clavijas de madera (C) en los agujeros de las clavijas de madera en la tabla de arriba (1). 3.
PASO 5 1. Atornille 3 pernos de leva (A) en los agujeros con rosca en el panel del lado izquierdo de abajo (2). 2. Sujete 1 soporte del cajón (E) al panel del lado izquierdo de abajo (2) insertando 2 tornillos para madera (D) en los agujeros del soporte del cajón (E), luego apriételos al panel del lado izquierdo de abajo (2). 3. Sujete el imán (M) al panel del lado izquierdo de abajo (2) insertando 2 tornillos (N) en los agujeros del imán (M) luego apriételos al panel del lado izquierdo de abajo(2). 4.
PASO 7 1. Inserte 4 clavijas de madera (C) en los agujeros de las clavijas de madera en la tabla de conexión del medio (18). 2. Sujete la unidad prearmada de arriba a la unidad prearmada de abajo insertando las clavijas de madera (C) en los agujeros de las clavijas de madera e insertando los pernos de leva (A) en los agujeros de las trabas de leva en el extremo de los paneles de los dos lados de abajo (2) y (3). 3.
PASO 9 PASO 9 1. Sujete 1 panel del costado del cajón (11) a la tabla de atrás del cajón (10) insertando 2 tornillos (F) en los agujeros del panel del costado del cajón (11) y luego apriételos a la tabla de atrás del cajón (10). 2. Repita el paso anterior para armar otro panel del costado del cajón (11) a la tabla de atrás del cajón (10). 3. Deslice la tabla del fondo del cajón (12) en las ranuras de ambos paneles de los costados del cajón (11). 4.
mardera (D) en los agujeros de las bisagras de metal (I), luego apriételos al panel del lado derecho de abajo (3). 5. Inserte 4 soportes de plástico (O) en los agujeros del panel del lado izquierdo de abajo (2) y panel del lado derecho de abajo (3). Los 4 soportes de plástico (O) deben estar a la misma altura. 6. Ponga el estante (6) en los soportes de plástico (O). PASO 11 PARED 1.
PASO 12 PARED 1. Ponga el armario contra la pared. 2. Inserte la tira de seguridad de plástico (T) por el soporte de metal (P) del armario y luego el soporte de metal (P) en la pared, sujete la tira de seguridad de plástico (T) para fijar con firmeza los 2 soportes de metal. Envíe pedidos de piezas dañadas o que faltan por correo electrónico a: customer.service@ssi-rr.com o llame gratis al 1-(844)-223-5201 o pida piezas en línea en www.riverridgehome.
¡DISFRUTE SU NUEVO ARMARIO de RiverRidge®! Atención adultos: Se debe inspeccionar periódicamente el armario para determinar si está dañado o hay piezas o tornillos flojos. Tome las medidas apropiadas necesarias para eliminar el peligro, tales como apretar los tornillos y mantener las piezas dañadas lejos de los niños. Gracias por comprar este producto RiverRidge® para el hogar. Esperamos que lo disfrute y que considere comprar otros productos RiverRidge®.