ASSEMBLY INSTRUCTIONS RiverRidge® Bayfield Single Door Floor Cabinet ITEM #: 06-113 White ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over. Don’t use this item for a TV stand or place heavy objects on top of item.
THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR A TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS OR 80 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20 POUNDS PER SHELF OR 80 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.
1 9 4 3 5 2 10 6 7 8 NO 1 2 3 4 5 6 7 8 9 10 QTY 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC DESCRIPTION Top Board Left Side Panel Right Side Panel Upper Cross Bar Adjustable Shelf Shelf Rear Lower Cross Bar Bottom Board Back Board Door
A B C D E F G H I J K L 12PCS Cam Bolt 12PCS Cam Lock 20PCS Wood Dowel (6 x 30mm) 4PCS Shelf Holder 2PCS Hinge 3PCS Screw (4 x 35mm) 8PCS Screw (4 x 12mm) 1PC Screw (4 x 30mm) 1PC Screw (4 x 12mm) 10PCS Screw (2.
STEP 1 A A A A A A A A 2 3 1. Insert 4 cam bolts (A) into pre-threaded holes on left side panel (2). 2. Insert 4 cam bolts (A) into pre-threaded holes on right side panel (3). STEP 2 A I A A L I L A 1 1. Insert 4 cam bolts (A) into pre-threaded holes on top board (1). 2. Attach bracket (L) to top board (1) by inserting 1 screw (I) through hole on bracket (L), then tighten to top board (1). STEP 3 8 7 F F 1.
STEP 4 G G E G G G G E E 10 1. Attach 2 hinges (E) to door (10) by inserting 4 screws (G) through holes on hinges (E), then tighten to door (10). STEP 5 7 6 4 8 B C C B C B C B C C 2 1. Insert 7 wood dowels (C) into wood dowel holes on left side panel (2). 2.
3 STEP 6 C C C C C C C 7 B 4 B B B 6 8 2 1. Insert 7 wood dowels (C) into wood dowel holes on right side panel (3). 2. Attach right side panel (3) to upper cross bar (4), shelf (6), bottom board (8) and rear lower cross bar (7) to by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A) into cam lock holes on upper cross bar (4), shelf (6) and bottom board (8). 3.
J STEP 8 J J J 9 J J J J J J 1. Attach back board (9) to back of cabinet by inserting 10 screws (J) through holes on back board (9), then tighten to cabinet. STEP 9 D D D D D 5 1. Insert 4 shelf holders (D) into desired position. 2. Place adjustable shelf (5) onto 4 shelf holders (D), making sure all shelf holders are at same level.
STEP 10 E G G G×2 c G×2 a a b 10 b c 1. Attach door (10) to cabinet by inserting 4 screws (G) through holes on hinges (E), then tighten to right side panel (3). 2. Note: Tightening screw in position “a” will adjust door up or down; tightening screw in position “b” will adjust door to or from cabinet, and tightening screw in position “c” will adjust door side to side.
STEP 11 K K H OPTION #1 H OPTION #2 DRYWALL H H WALL ANCHOR WITH SCREW DRYWALL K WOOD STUD SCREW ONLY Option #1: Securing to Drywall 1. Position cabinet against wall in desired location. Using a pencil, make a small mark on wall through hole on bracket (L). Move cabinet away from wall and screw 1 plastic anchor (K) into wall on pencil mark. 2. Place cabinet against wall, insert 1 screw (H) through hole on metal bracket (L), then tighten to plastic anchor (K).
Enjoy your new RiverRidge ® Cabinet! Thank you for purchasing this RiverRidge ® Home item. We hope you enjoy it and consider purchasing other RiverRidge ® items. To order replacement parts at no cost to you, email customer.service@ssi - rr.com, call 1-(844) -223-5201 or order parts online at www.riverridgehome.com RiverRidge ® is a registered trademark of Sourcing Solutions, Inc.
