Operator's Manual WE ARE HUNTERS BIG FOOT™ XC Hang-On Stand MODEL RE559 Maximum Field Rating 300 lbs Tree Diameter Range 8" to 20" Wear Your Harness! PRODUCT MEETS INDUSTRY STANDARDS RECOGNIZED BY Get parts online at www.HuntRiversEdge.
Operator's Manual BIG FOOT XC Hang-On Stand INTRODUCTION Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free pleasure. Instructions should be kept in a safe place and reviewed at least annually.
Operator's Manual BIG FOOT XC Hang-On Stand STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY MODEL RE559 MAXIMUM OCCUPANCY - ONE (1) PERSON TOTAL WEIGHT LIMIT - 300 LB TREE DIAMETER RANGE - 8" TO 20" WARNING This product carries strict weight restrictions. Do Not use this product if you exceed the total weight limit. Please note that the total weight limit includes the user(s) and their equipment.
Operator's Manual BIG FOOT XC Hang-On Stand WARNING INSPECTION AND MAINTENANCE Climbing aids (stick ladders, sectional ladders, steps, etc.) must extend above the platform to allow the user to step down onto the platform. Never step up to your stand from a climbing aid. To ensure that you step down onto the platform, the maximum recommended use height is five feet less than the height of the climbing aid being used.
Bolts shown are for size reference. Extra hardware may be included in the parts bag.
Operator's Manual BIG FOOT XC Hang-On Stand ASSEMBLY INSTRUCTIONS TOOLS NEEDED: two 1/2 IN wrenches two 7/16 IN wrenches All assembly must be done in this order at ground level before use. Do not remove labels/warnings from product, they are there for your safety. Recommended for adult use only. NOTE: When selecting a tree to install the treestand in, never use a treestand on a dead, leaning, diseased or loose barked tree, or a utility pole. Always avoid electrical power lines. 1 1.
Operator's Manual FIGURE 3 BIG FOOT XC Hang-On Stand 3 7 3. Bolt cables (7) onto platform (3) using two 5/16-18 X 1-1/2 IN bolts (11), two washers (18) and two 5/16-18 nuts (17). SEE FIGURE 3. 17 18 11 4. Attach the footrest (6) onto the platform (3) using two 1/4-20 X 2-1/4 IN bolts (15), two plastic washers (9) and two 1/4-20 nuts (16). SEE FIGURE 4. Note: You must now tighten all nut and bolt assemblies. Be sure not to over-tighten or crush tubing while tightening! FIGURE 4 5.
Operator's Manual BIG FOOT XC Hang-On Stand STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE WARNING WARNING Double check assembly steps to be certain you have correctly assembled this product. Do Not twist strap when attaching. See setup and use instructions for correct attachment. Practice installing, adjusting and using your treestand at ground level prior to using it at elevated positions. Study your new stand to become familiar with all of its features and design.
Operator's Manual BIG FOOT XC Hang-On Stand SETUP AND USE INSTRUCTIONS During installation and removal of a hang-on treestand, you must always and properly use the included Full Body Harness (Fall Arrest System) with climbing belt. Refer to the Full Body Harness and climbing belt instructions included with this product for proper use. You must always use the Full Body Harness while using this product.
Operator's Manual BIG FOOT XC Hang-On Stand TREE ATTACHMENT INSTRUCTIONS 1. At desired height, attach by following instructions - a,b,c,d,e,f. NOTE: Stand should be attached to tree with platform folded in an upright position! WARNING Platform must be folded up to remove stand! This allows slack in strap for removal. a. Lengthen strap by pulling float buckle away from strap - this will allow strap to slide around float buckle roller bar. b.
Operator's Manual BIG FOOT XC Hang-On Stand THREADING THE FLOAT BUCKLE Always check the condition of your Big Foot strap before use. If strap becomes twisted or if you need to replace a worn or damaged strap, make sure to follow these instruction to ensure proper assembly. 1. Hold float buckle so warning tag faces upward. SEE FIGURE 11. 2. Feed end tail of strap up through the bottom of the float buckle on the sewn loop side of the roller bar. SEE FIGURE 12.
Operator's Manual BIG FOOT XC Hang-On Stand ILLUSTRATED PARTS BREAKDOWN PARTS LIST 2 20 16 4 21 9 5 16 19 12 9 8 1 14 18 10 16 13 7 KEY # PART # DESCRIPTION QTY.
Operator's Manual BIG FOOT XC Hang-On Stand NOTES 14 Check for parts online at www.HuntRiversEdge.
Operator's Manual BIG FOOT XC Hang-On Stand OTHER GREAT PRODUCTS BY RIVERS EDGE TREESTANDS Portable ground blinds take a beating from the sun, wind, rain and snow. Colors fade, materials rot, poles break and fabric tears. The Landmark Permanent Blind was designed and constructed to resist the elements year after year. The durable steel frame is covered in marine-grade reinforced synthetic tarpaulin, made from the same rugged materials used in pick-up truck tonneau covers.
by WE ARE HUNTERS Rivers Edge® Treestands, Inc. Phone: 800-450-EDGE (3343) 1160 Eighth Avenue, PO Box 755 Fax: 715-822-2124 Cumberland, WI 54829 Email: info@huntriversedge.com *All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included.