Operator's Manual WE ARE HUNTERS LOCKDOWN™ WIDE 1-MAN Ladder Stand MODEL RE655 Maximum Height 18' 6” to shooting rail Maximum Field Rating 300 lbs Tree Diameter Range 12" to 20" Wear Your Harness! PRODUCT MEETS INDUSTRY STANDARDS RECOGNIZED BY Get parts online at www.HuntRiversEdge.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand INTRODUCTION Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free pleasure. Instructions should be kept in a safe place and reviewed at least annually.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY MODEL RE655 MAXIMUM USE HEIGHT - 18' 6” TO SHOOTING RAIL MAXIMUM OCCUPANCY - ONE (1) PERSON TOTAL WEIGHT LIMIT - 300 LB TREE DIAMETER RANGE - 12” TO 20” WARNING This product carries strict height and weight restrictions. Do Not use this product if you exceed the total weight limit. Please note that the total weight limit includes the user(s) and their equipment.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand WARNING INSPECTION AND MAINTENANCE Always lean forward as you climb and attach your harness to the tree before securing the platform to the tree and stepping onto the platform. Never exceed the stated maximum use height. Do Not use this product until you have watched the included treestand safety DVD, understand it, and practiced the techniques for safe hunting discussed in this DVD.
Bolts shown are for size reference. Extra hardware may be included in the parts bag.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand ASSEMBLY INSTRUCTIONS IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations completely until all parts are assembled together! Finger tighten plus one turn of a wrench only! This will temporarily hold the lock- nut on the bolt while helping alignment of all parts! After all parts are assembled together, all nut and bolt combinations must be completely tightened. All assembly must be done in this order at ground level before uprighting.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand 18 FIGURE 3 19 41 3. 11 Attach one backrest (18) to the back of each armrest (11, 12) using two 1/4-20 x 2-1/4 IN bolts (41) and two 1/4-20 IN nuts (44) for each assembly. SEE FIGURE 3 44 39 18 44 17 21 8 Slide the TearTuff backrest (21) over each of the secured backrests (18). After this has been completed, assemble the back rest spreader (17) with one 1/4-20 x 1-1/2 IN bolt (39) and one 1/4-20 IN nut (44) on each end.
Operator's Manual FIGURE 5A LOCKDOWN WIDE 1-MAN Ladder Stand 15 5. Screw the M6 x 70 MM bolt (30) into the opposite end of the front seat tensioner (15) until snug. SEE FIGURE 5A 6. Slide the front seat tensioner (15) assembly from figure 5A through the open tube mount on the lower front edge of the seat assembly (13) such that the bolt end of the front seat tensioner bumps up against the closed end of the other tube mount. Make sure the bolt holes line up in the open tube mount. SEE FIGURE 5 7.
Operator's Manual FIGURE 7 LOCKDOWN WIDE 1-MAN Ladder Stand 39 44 14 10. Take the rear seat supports (14) and attach them to the correct bracket on each seat side rail (9) using one 1/4-20 x 1-1/2 IN (39) and a 1/4-20 nut (44). SEE FIGURE 7 11. Attach the platform rails (8) to the lower end of each seat side rail (9) using a 1/4-20 x 1-3/4 IN bolt (40) and a 1/4-20 nut (44) for each side. SEE FIGURE 7 9 40 44 8 13.
Operator's Manual FIGURE 9 LOCKDOWN WIDE 1-MAN Ladder Stand 14. Connect the first ladder section (3) to the platform rails (8) with a 1/4-20 x 1-3/4 IN bolt (40) and a 1/4-20 nut (44) on each side of the ladder. Once connected, attach the free end of the platform braces (16) to the outer edge of the ladder section (3) with a 1/4-20 x 2-1/4 IN bolt (38), one yellow washer (25) and a 1/4-20 nut (44) on each side. SEE FIGURE 9 8 40 16 25 44 38 3 15.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand 22 10 46 44 FIGURE 11 11 31 28 19 17. Assemble the adjustable shooting rail knobs (31) and bolts (28) to the armrests (11, 12) in the slots provided. To assemble the shooting rest, connect the shooting rail (10) over the ends of both the shooting rail braces (22) and secure using two 1/4-20 x 1-1/4 IN bolts (46) and two 1/4-20 nuts (44). SEE FIGURE 11 18. The shooting rail assembly connects to the armrest as shown in Figure 12.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand 3 4 7 5 FIGURE 13 FIGURE 13A 19. Ladder sections are assembled on the ground in the following order: bottom ladder section (5), middle ladder section with stabilizer slot (7), middle ladder section (4), and the top ladder section (3) with the treestand top assembly. Connect all sections together using the six silent knob assemblies (26).
Operator's Manual FIGURE 15A LOCKDOWN WIDE 1-MAN Ladder Stand 2 49 LONG CRISS-CROSS RATCHET STRAPS (49) 22. Attach the two long straps of the criss-cross ratchet straps (49) to the rear of the foot platform (2) near the lower tree blade. FIGURE 15B FIGURE 15 2 49 a. Wrap sewn loop of each strap around each side of the platform and feed the loose end through the sewn loop. SEE FIGURES 15A AND 15B b. Pull tight, forming a cinch knot.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE WARNING Double check assembly steps to be certain you have correctly assembled this product. Study your new stand to become familiar with all of its features and design. At ground level, following provided use instructions, practice attaching stand to tree and re- moving stand from tree. Practice sitting, standing, and using this product before attaching overhead.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand SET UP AND USE INSTRUCTIONS During installation and removal of ladder treestands, you must always and properly use the included Full Body Harness (Fall Arrest System). Refer to the Full Body Harness instructions included with this product for proper use. 1. Select a straight, healthy tree. Do Not attempt to install on a tree that is not healthy. 2.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand 10. Locate the two ratchet portions with S-hooks for the crisscross straps (49). a. With one ratchet portion of the criss-cross strap (49) now in hand, feed one long strap hanging down from platform through the center slot of ratcheting mechanism and back around through tightening lever. SEE FIGURES 18A AND 18B b.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand FINISHED LADDER ADJUSTABLE VINYL DIPPED SHOOTING RAIL FOOTREST LARGE RATCHET STRAPS LONG CRISS-CROSS RATCHET STRAPS SILENT KNOB ASSEMBLIES STABILIZER BAR RATCHET STRAP ADJUSTABLE BARK BITING STABILIZER BAR 18 Check for parts online at www.HuntRiversEdge.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand ILLUSTRATED PARTS BREAKDOWN 27 46 22 10 12 34 18 17 39 43 Mesh hidden for clarity 29 3 39 33 19 13 26 14 45 4 36 11 25 15 38 30 2 1 28 44 9 8 37 29 39 41 23 41 24 40 31 42 40 35 33 7 33 6 32 43 16 29 20 41 5 Check for parts online at www.HuntRiversEdge.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand PARTS LIST ITEM # PART # DESCRIPTION QTY. ITEM # PART # DESCRIPTION 1 23775 2 QTY.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand NOTES: Check for parts online at www.HuntRiversEdge.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand NOTES: 22 Check for parts online at www.HuntRiversEdge.
Operator's Manual LOCKDOWN WIDE 1-MAN Ladder Stand OTHER GREAT PRODUCTS BY RIVERS EDGE TREESTANDS Portable ground blinds take a beating from the sun, wind, rain and snow. Colors fade, materials rot, poles break and fabric tears. The Landmark Permanent Blind was designed and constructed to resist the elements year after year. The durable steel frame is covered in marine-grade reinforced synthetic tarpaulin, made from the same rugged materials used in pick-up truck tonneau covers.
by WE ARE HUNTERS Rivers Edge® Treestands, Inc. Phone: 800-450-EDGE (3343) 1160 Eighth Avenue, PO Box 755 Fax: 715-822-2124 Cumberland, WI 54829 www.HuntRiversEdge.com *All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.