Product Manual

ManualsBrandsRiverside Pumps ManualsGas218 GPM (2.5") High Pressure Fire Fighting Pump w/ B & S Vanguard™ Engine

PRESSURE PUMP

MODEL / UT NUMBER / DESCRIPTION:

FP25V L1293Y 2½-INCH PRESSURE PUMP, VANGUARD 13 ENGINE

FP25VI L1619Z 2½-INCH PRESSURE PUMP, VANGUARD 13 ENGINE

FP25H L1610Z 2½-INCH PRESSURE PUMP, HONDA GX390 ENGINE

FP25HE L1617Z 2½-INCH PRESSURE PUMP, HONDA GX390 ENGINE, ELECTRIC START

FP25K L1690Z 2½-INCH PRESSURE PUMP, KOHLER CS-12 ENGINE

FP25Y L1625Z 2½-INCH PRESSURE PUMP, YANMAR DIESEL ENGINE

FP25YE L1626Z 2½-INCH PRESSURE PUMP, YANMAR DIESEL ENGINE, ELECTRIC START

INSTRUCTIONS & PARTS LIST

SYMBOL DEFINITION

Do not pump flammable materials. Fire could occur.

Do not pump hazardous material.

Read your product literature before use.

Do not smoke or bring flame near gasoline.

Disconnect spark plug before performing

maintenance, adjustment, lubrication, and

storage.

Part No. L00247

Rev. H 2010/06/01

SAFETY PRECAUTIONS

• This pump is designed for pumping clean water only. It should not be

used to pump sandy water or hazardous fluids.

• Before start-up, study all of the instructions in this manual. Be sure

you thoroughly understand how to operate the pump. Proper

preparation, operation and simple maintenance will improve operator

safety, pump performance and long unit life.

• Be sure that each person who operates the machine is properly

instructed as to its safe operation.

• Always keep the machine and associated equipment clean, properly

serviced and maintained according to the instructions in this manual.

• Observe all safety regulations for the safe handling and storage of

fuel. Handle fuel in approved vented fuel cans. Do not store fuel

supplies in a garage, shed or other areas attached to living quarters.

Do not refill the fuel tank in an area attached to living quarters. Do not

refill the engine while it is running or hot. Carefully clean up any

spilled fuel before starting the engine.

• Do not smoke or bring flame near gasoline.

• Do not operate the pump at shut-off pressure for more than 2 minutes.

• Do not operate this pump if any safety equipment or guard has been

removed.

• Never operate the machine in any explosive atmosphere, near

combustible materials, or where there is not enough ventilation to

carry off the exhaust fumes. DO NOT operate pump indoors or in crawl

spaces.

• Always be sure the machine is on secure footing and cannot shift to

where it might injure someone. Remember that the suction hose on

the pump tends to pull the pump towards the liquid source during

pumping.

• Keep the immediate area free of bystanders.

• When pulling the starter, be sure that nothing is in a position to be hit

by the operator’s hand or arm, or the starting rope.

• Do not touch the hot cylinder and muffler area.

• Shut off the engine and disconnect the spark plug wire before working

on any part of the machine.

• Long or continuous exposure to high noise levels, such as the

operation of a gasoline engine, may cause permanent hearing

impairment or other possible effects. Hearing protection devices are

available from your dealer, or can be ordered through him.

• The discharge hose used with the FP25 must be able to withstand a

maximum pressure of 150 PSI (10.34 BAR).

• Use only genuine product manufacturer’s replacement parts. Failure

to do so may cause poor fit and possible injury.

•

BEWARE OF USING THIS EQUIPMENT IN CONFINED SPACES.BEWARE OF USING THIS EQUIPMENT IN CONFINED SPACES.

BEWARE OF USING THIS EQUIPMENT IN CONFINED SPACES.

Confined spaces, without sufficient fresh air ventilation, can contain

dangerous gases. Running gasoline engines in such environments

can lead to deadly explosions and/or asphyxiation.

Summary of content (16 pages)

PAGE 1
PRESSURE PUMP FP25V FP25VI FP25H FP25HE FP25K FP25Y FP25YE L1293Y L1619Z L1610Z L1617Z L1690Z L1625Z L1626Z MODEL / UT NUMBER / DESCRIPTION: 2½-INCH PRESSURE PUMP, VANGUARD 13 ENGINE 2½-INCH PRESSURE PUMP, VANGUARD 13 ENGINE 2½-INCH PRESSURE PUMP, HONDA GX390 ENGINE 2½-INCH PRESSURE PUMP, HONDA GX390 ENGINE, ELECTRIC START 2½-INCH PRESSURE PUMP, KOHLER CS-12 ENGINE 2½-INCH PRESSURE PUMP, YANMAR DIESEL ENGINE 2½-INCH PRESSURE PUMP, YANMAR DIESEL ENGINE, ELECTRIC START INSTRUCTIONS & PARTS LIST SYMBOL DEF
PAGE 2
THE FP25 STRAINER The FP25 is ideal for handling clean water, free of solids and debris, and for conditions where long hose runs are needed. Primarily used for firefighting and emergencies, the FP25 can also be used for highperformance jetting, sprinkler systems, irrigation and water supply, and for the washing and cleaning of equipment. The strainer supplied with this pump is designed to fit a 4-inch hose. The strainer orifices are sized to permit passage of solids that the unit is designed to handle.
PAGE 3
OPERATING INSTRUCTIONS PREPARING FOR STORAGE 1. Use a strainer on the end of the suction line. 2. Make sure that all hose and pipe connections are air tight. An air leak in the suction line may prevent priming and will reduce the lift capacity of the pump. 3. Place the pump as close to the liquid to be pumped as possible. Keep the pump and engine on a level foundation.
PAGE 4
POMPE REFOULANTE FP25V FP25VI FP25H FP25HE FP25K FP25Y FP25YE L1293Y L1619Z L1610Z L1617Z L1690Z L1625Z L1626Z MODÈLE / UT NOMBRE / DESCRIPTION: 2½" POMPE HAUTE PRESSION, VANGUARD 13MOTEUR 2½" POMPE HAUTE PRESSION, VANGUARD 13MOTEUR 2½" POMPE HAUTE PRESSION, HONDA GX390 MOTEUR 2½" POMPE HAUTE PRESSION, HONDA GX390 MOTEUR, DÉMARRAGE - ÉLECTRIQUE 2½" POMPE HAUTE PRESSION, KOHLER CS-12 MOTEUR 2½" POMPE HAUTE PRESSION, YANMAR DIESEL MOTEUR 2½" POMPE HAUTE PRESSION, YANMAR DIESEL MOTEUR, DÉMARRAGE - ÉLECTRIQU
PAGE 5
LA FP25 CRÉPINE La FP25 est idéale pour les endroits où l’eau est propre, sans solides et débris, et lorsqu’il est nécessaire d’avoir un long tuyau. Bien qu’elle soit essentiellement utilisée pour combattre les incendies et dans les cas d’urgence, la FP25 peut également servir pour le fonçage au jet d’eau à haute performance, les systèmes de gicleur, l’irrigation et l’alimentation en eau, ainsi que pour laver ou nettoyer des machines.
PAGE 6
DIRECTIVES DE FONCTIONNEMENT ENTREPOSAGE DE L’APPAREIL 1. Il est préférable de mettre un filtre à la fin de la tuyauterie d’aspiration. 2. Veillez à ce que tous les raccords de boyaux et de tuyaux soient bien étanches. S’il y a une fuite dans la tuyauterie d’aspiration, l’amorçage risque de ne pas se faire et la capacité d’aspiration de la pompe sera réduite. 3. Placez la pompe aussi près du liquide à pomper que possible. Posez la pompe et le moteur sur une base plane.
PAGE 7
MOTOBOMBA DE PRESIÓN FP25V FP25VI FP25H FP25HE FP25K FP25Y FP25YE L1293Y L1619Z L1610Z L1617Z L1690Z L1625Z L1626Z MODELO / UT NÚMERO / DESCRIPCIÓN: 2½" BOMBA DE PRESIÓN, VANGUARD 13 MOTOR 2½" BOMBA DE PRESIÓN, VANGUARD 13 MOTOR 2½" BOMBA DE PRESIÓN, HONDA GX390 MOTOR 2½" BOMBA DE PRESIÓN, HONDA GX390 MOTOR, ARRANQUE - ELÉCTRICO 2½" BOMBA DE PRESIÓN, KOHLER CS-12 MOTOR 2½" BOMBA DE PRESIÓN, YANMAR DIESEL MOTOR 2½" BOMBA DE PRESIÓN, YANMAR DIESEL MOTOR, ARRANQUE - ELÉCTRICO MANUAL DEL PROPIETARIO Y LISTA
PAGE 8
LA UNIDAD FP25 ALCACHOFA DE ASPIRACION La unidad FP25 es ideal para el bombeo de agua limpia, sin sólidos ni residuos en suspensión, y para bombeo con tramos largos de manguera. La unidad FP25 se usa principalmente para combatir incendios y en situaciones de emergencia, pero también se puede utilizar para chorros a alta presión, sistemas de riego, suministro de agua potable y para lavado y limpieza de equipos y maquinarias.
PAGE 9
INSTRUCCIONES DE USO ALMACENAMIENTO DE LA UNIDAD 1. Es conveniente usar una malla de filtro en el extremo de la línea de aspiración. 2. Verificar la hermeticidad de todas las conexiones de mangueras y tuberías. Una entrada de aire en la línea de aspiración puede dificultar e incluso impedir el cebado, reduciendo consecuentemente la presión de bombeo. 3. Instalar la bomba tan cerca como sea posible del líquido a bombear, y montar la unidad motor-bomba sobre una superficie nivelada.
PAGE 10
DRUCKPUMPE FP25V FP25VI FP25H FP25HE FP25K FP25Y FP25YE L1293Y L1619Z L1610Z L1617Z L1690Z L1625Z L1626Z MODELL / UT NUMMER / BESCHREIBUNG: 2½" DRUCKPUMPE, VANGUARD 13 MOTOR 2½" DRUCKPUMPE, VANGUARD 13 MOTOR 2½" DRUCKPUMPE, HONDA GX390 MOTOR 2½" DRUCKPUMPE, HONDA GX390 MOTOR, STARTSYSTEM - ELEKTRISCH 2½" DRUCKPUMPE, KOHLER CS-12 MOTOR 2½" DRUCKPUMPE, YANMAR DIESEL MOTOR 2½" DRUCKPUMPE, YANMAR DIESEL MOTOR, STARTSYSTEM - ELEKTRISCH ANLEITUNG UND TEILELISTE ERKLÄRUNG DER SYMBOLE Keine brennbaren Materiali
PAGE 11
DIE DRUCKPUMPE FP25 SIEB Die Druckpumpen FP25 werden auf unterschiedliche Weise genutzt, zum Beispiel bei der Brandbekämpfung, der Reinigung von Frachtschiffen und Anlagen oder der Beregnung von Nutzpflanzen. Sie zeichnen sich aus durch eine hohe Förderleistung und einen hohen Druck. Das mit dieser Pumpe mitgelieferte Sieb ist für einen 2.5-Zoll-Schlauch gedacht. Die Sieböffnungen sind so groß, dass sie Feststoffe hindurchlassen, für die das Gerät ausgelegt ist.
PAGE 12
BETRIEBSANLEITUNG VORBEREITEN DER PUMPE FÜR ABLAGE 1. Verwenden Sie ein Sieb am Ende der Saugleitung. 2. Stellen Sie sicher, dass alle Schlauch- und Rohranschlüsse luftdicht sind. Eine Luftdurchlässigkeit in der Saugleitung kann das Vorfüllen verhindern und verringert die Hubleistung der Pumpe. 3. Stellen Sie die Pumpe so nah wie möglich zur zu pumpenden Flüssigkeit. Stellen Sie die Pumpe und den Motor auf eine ebene Grundlage.
PAGE 13
EINGESCHRÄNKTE GARANTIE Riverside Pump Manufacturing Inc. garantiert gegenüber dem ursprünglichen Käufer, dass dieses Produkt von Riverside Pump Manufacturing Inc. frei von Material- und Fertigungsfehlern ist, und erklärt sich damit einverstanden, nach eigenem Ermessen von Riverside Pump Manufacturing Inc., defekte Produkte innerhalb eines Zeitraums von zwei Jahren ab Kaufdatum kostenlos zu reparieren oder zu ersetzen.
PAGE 14
PARTS LIST / LISTE DE PIECES DE RECHANGE / LISTA DE PARTES / TEILELISTE 17 16 18 15 13 12 10 3 7 8 22 24 1 19 9 32 14 30 43 44 11 35 21 20 9 25 26 2 4 5 6 23 42 37 36 39 REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 15005 15011 15012 15229 15044 15045 20629 A 48843 1A 47447 15016 PA 00125 47468 80095 15056 84010 84046 81225 48488 48845 47361 80676 48844 1A 83116 82479 47048 80098 80446 84035 47364 1A DESCRIPTION QTY. Engine, Vanguard OHV, 13 hp (FP25V) .........
PAGE 15
PARTS LIST / LISTE DE PIECES DE RECHANGE / LISTA DE PARTES / TEILELISTE FP25V / FP25VI / FP25H / FP25HE / FP25K FP25Y / FP25YE 1* 1 4* 5* 2* 3* 5* 4* * Included in A 15025 Roll Cage Kit REF. PART NO. *1 PA 00097 *2 PA 00098 1 PA 00098 *3 49367 *4 81162 *5 83002 DESCRIPTION QTY. Roll Cage (FP25V/VI/H/HE/K) ........................ 1 Engine Support (FP25H/HE/K) ......................... 1 Engine Support (FP25V/VI) .................................. 1 Isolator .........................................
PAGE 16