RJS2032 RJ Speed 1-10 Classic Sprint Kit Instructions

ManualsBrandsRJ Speed ManualsCars & Trucks1/10 Classic Sprint Kit

2032 3 in 1 CLASSIC SPRINT CAR KIT

THANKS FOR BUYING THE RJ SPEED CLASSIC SPRINTER KIT. IT IS COMPLETE LESS ELECTRICS, AND

MADE FOR CARPET OR PAVEMENT RACING. IT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY

PACK, TWO CHANNEL RADIO WITH ESC, AND A SERVO SAVER TO FIT THE BRAND OF RADIO YOU HAVE CHO-

SEN. THE TOOLS YOU WILL NEED ARE A SMALL PAIR OF PLIERS, A 1/4 “ SOCKET OR WRENCH, AND A 7/16 “

SOCKET WRENCH FOR THE DIFFERENTIAL. HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE IN-

CLUDED IN THE KIT. YOU WILL ALSO NEED PAINT MADE FOR LEXAN FOR THE BODY PARTS . REFER TO THE

TEXT AND PICTURES FOR EACH STEP , AND ALSO THE EXPLODED VIEW DRAWING FOR THE CHASSIS AS-

SEMBLY AND PARTS REFERENCE AND THE BODY TRIM AND ASSEMBLY DRAWINGS.

IT IS BEST TO READ EACH STEP THROUGH, LOOK AT THE PICTURES,

DRAWINGS, AND PARTS , THEN DO THE ASSEMBLY STEP.

YOUR KIT CONTAINS THE FOLLOWING:

CLASSIC INDY ROADSTER AND

CHAMP CAR BODY KITS

INSTRUCTION PKG. WITH SERVO

TAPE AND RJ SPEED DECALS

BAG J1 CHASSIS KIT

BAG L2 REAR AXLE PARTS

BAG L4 FRONT TIRES

BAG L5 REAR TIRES

HARDWARE I.D.

BUTTON HD. CAP SCREW

1/4 3/8 1/2 1/4 3/8 1/2

STEP 1 OPEN BAG J1 . ATTACH SIX CHASSIS SPAC-

ERS TO EITHER CHASSIS SIDE . USE 1/2” BUTTON HEAD

SCREWS WITH 2434 MOUNTS ON THEM ON THE

TOP REAR AND 2ND FROM THE FRONT. USE 3/8 LONG

BUTTON HEAD SCREWS ON THE BOTTOM REAR AND

FRONT SPACERS. USE 3/8 CAP SCREWS ON THE TWO

REMAINING TWO SPACERS.

STEP 2 INSTALL THE FRONT AXLE PLATE, SERVO

PLATE , AND BATTERY TRAY IN THE CHASSIS SIDE .

STEP 4 OPEN THE

STEERING BAG FROM

BAG J1 AND THREAD

A JAM NUT ON EACH

5377 KINGPIN, INSERT

INTO EACH END OF

THE FRONT AXLE

PLATE, AND ADD A

7207 LOCKNUT ON

EACH ONE.

STEP 3 INSTALL THE 2ND CHASSIS SIDE USING

THE SAME LAYOUT AS STEP 1 FOR SCREW TYPES

AND PLACEMENT OF THE 2434 MOUNTS.

Summary of content (6 pages)

PAGE 1
2032 3 in 1 CLASSIC SPRINT CAR KIT THANKS FOR BUYING THE RJ SPEED CLASSIC SPRINTER KIT. IT IS COMPLETE LESS ELECTRICS, AND MADE FOR CARPET OR PAVEMENT RACING. IT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY PACK, TWO CHANNEL RADIO WITH ESC, AND A SERVO SAVER TO FIT THE BRAND OF RADIO YOU HAVE CHOSEN. THE TOOLS YOU WILL NEED ARE A SMALL PAIR OF PLIERS, A 1/4 “ SOCKET OR WRENCH, AND A 7/16 “ SOCKET WRENCH FOR THE DIFFERENTIAL. HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE INCLUDED IN THE KIT.
PAGE 2
STEP 5 PRESS A 5364 STUB AXLE INTO EACH 5351 STEERING BLOCK AND RETAIN WITH A 5221 E-CLIP. STEP 6 LUBE EACH KINGPIN, SLIDE THE STEERING BLOCK ON, ADD A 5228 SPRING , WASHER , AND E-CLIP. STEP 7 INSTALL THE 5188 RIDE HEIGHT ADAPTORS FROM BAG L2 AND ADD THE 5452 REAR BUSHINGS. STEP 8 SNAP A DIFF BALL INTO EVERY OTHER HOLE IN THE OUTSIDE ROW OF THE GEAR. LUBE EACH ONE WITH A LITTLE THICK SILICONE OR GREASE.
PAGE 3
STEP 12 INSTALL YOUR SERVO SAVER ON THE SERVO AND ATTACH THE SERVO UNDER THE SERVO PLATE WITH FOAM TAPE PROVIDED. GET THE SERVO SAVER AS CLOSE TO THE CENTER AS POSSIBLE. MAKE SURE TO WIPE THE SERVO AND SERVO PLATE WITH A DRY CLOTH BEFORE APPLYING THE TAPE. STEP 13 INSTALL THE STEERING LINKAGE FROM BAG H3. INSTALL A LONG LINK IN EACH STEERING BLOCK AND TWO SHORT ONES IN THE SERVO SAVER. USE THE COLLARS AND SET SCREWS TO ATTACH THE RODS TOGETHER AFTER ALIGNING THE STEERING.
PAGE 4
NOTE THAT THE TWO DRIVER FIGURES ARE DIFFERENT. ONE IS MARKED ROADSTER TO GO ON THE OPEN COCKPIT BODY. USE A SMALL PC. OF SERVO TAPE IN THE LAP AREA TO ATTACH IT. THE OTHER ONE IS SLIGHTLY NARROWER TO FIT INSIDE THE ROLL CAGE. USE TAPE TO ATTACH THE SIDES TO THE BODY. REAR STEP 18 REFER TO THE BODY DRAWINGS FOR TRIMMING AND MOUNTING OF THE ACCESSORY PARTS. PAINT THE BODIES ,HEADERS AND WING FROM THE INSIDE.
PAGE 5
7206 HARDWARE 3/8 CAP SCREWS 3/8 BTN.HD SCREWS 1/2 BTN.
PAGE 6
CUT OUT BODY MOUNT HOLES MOUNT THE WINDSHIELD , HEADERS , DRIVER, AND INJECTORS WITH DOUBLE BACKED TAPE . DRILL FOUR 1/8 HOLES AS MARKED AND ATTACH THE ROLL BAR WITH FOUR SMALL SCREWS PROVIDED. PAINT THE BODY AND DRIVER. TRIM OUT AS SHOWN. DRILL BODY MOUNT HOLES 1/4”. 1047 INDY ROADSTER CLASSIC CHAMP CAR CUT OUT WING MOUNT BODY MOUNT HOLES REAR OVERLAP PAINT THE BODY AND DRIVER, AND WING IF YOU ARE GOING TO USE IT. TRIM OUT AS SHOWN. DRILL BODY MOUNT HOLES 1/4”.