RJS2030 RJ Speed 1-10 Outlaw Sprinter Instructions

ManualsBrandsRJ Speed ManualsCars & Trucks1/10 Outlaw Sprinter Kit

THANKS FOR BUYING THE RJ SPEED OUTLAW SPRINTER KIT. IT IS COMPLETE LESS ELECTRICS, AND

MADE FOR CARPET OR PAVEMENT RACING. IT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY

PACK, TWO CHANNEL RADIO WITH ESC, AND A SERVO SAVER TO FIT THE BRAND OF RADIO YOU HAVE CHO-

SEN. THE TOOLS YOU WILL NEED ARE A SMALL PAIR OF PLIERS, A 1/4 “ SOCKET OR WRENCH, AND A 7/16 “

SOCKET WRENCH FOR THE DIFFERENTIAL. HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE IN-

CLUDED IN THE KIT. YOU WILL ALSO NEED PAINT MADE FOR LEXAN FOR THE BODY PARTS AND WINGS. RE-

FER TO THE TEXT AND PICTURES FOR EACH STEP , AND ALSO THE EXPLODED VIEW DRAWING FOR THE

CHASSIS ASSEMBLY AND PARTS REFERENCE AND THE WING TRIM AND ASSEMBLY DRAWINGS

IT IS BEST TO READ EACH STEP THROUGH, LOOK AT THE PICTURES,

DRAWINGS,AND PARTS , THEN DO THE ASSEMBLY STEP.

YOUR KIT CONTAINS THE FOLLOWING:

2030 OUTLAW SPRINTER

BAG L5 REAR TIRES

1043 BODY PARTS

1525 WING PARTS

INSTRUCTION PKG.

BAG H1 CHASSIS KIT

BAG H3 HARDWARE

BAG L2 REAR AXLE PARTS

BAG L4 FRONT TIRES

STEP 1 OPEN BAG H1 AND H1A. ATTACH THE 5065 NERF

BARS TO THE CHASSIS SIDES WITH 3/8 CAP SCREWS. RE-

FER TO THE HARDWARE ID FOR SCREW SIZES. INSERT THE

SCREW FOR THE REAR OF THE LEFT NERF BAR THRU THE

TIE BAR , THEN THE CHASSIS AND INTO THE NERF BAR.

STEP 2 ATTACH FOUR 5245 CHASSIS SPACERS TO THE

RIGHT CHASSIS SIDE WITH 3/8 CAP SCREWS. USE A 3/8

BUTTON HEAD ON THE FRONT ONE.

STEP 3 SLIDE THE FRONT AXLE PLATE, SERVO TRAY AND

RADIO TRAY INTO THE SLOTS IN THE CHASSIS SIDE.

STEP 4 SLIDE THE LEFT CHASSIS OVER THE PARTS AND

ATTACH WITH 3/8 CAP SCREWS (BUTTON HD. ON FT.).SET

THE CHASSIS ON YOUR TABLE TO MAKE SURE IT SITS FLAT.

IF NOT, HOLD BOTH ENDS AND TWIST TO CORRECT. CHECK

IT AGAIN AFTER INSTALLING THE REAR BARS AND CAGE.

HARDWARE I.D.

BUTTON HD. CAP SCREW

1/4 3/8 1/2 1/4 3/8 1/2

TIE BAR

RJS 9-09-13

Summary of content (8 pages)

PAGE 1
2030 OUTLAW SPRINTER THANKS FOR BUYING THE RJ SPEED OUTLAW SPRINTER KIT. IT IS COMPLETE LESS ELECTRICS, AND MADE FOR CARPET OR PAVEMENT RACING. IT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY PACK, TWO CHANNEL RADIO WITH ESC, AND A SERVO SAVER TO FIT THE BRAND OF RADIO YOU HAVE CHOSEN. THE TOOLS YOU WILL NEED ARE A SMALL PAIR OF PLIERS, A 1/4 “ SOCKET OR WRENCH, AND A 7/16 “ SOCKET WRENCH FOR THE DIFFERENTIAL. HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE INCLUDED IN THE KIT.
PAGE 2
STEP 5 ATTACH THE REAR BARS AND CHASSIS SPACERS TO THE REAR OF THE CHASSIS WITH FOUR 1/2” BUTTON HEAD SCREWS. STEP 6 USE TWO 1/2” CAP SCREWS AND THE 1/2” NYLON SPACER TO ATTACH THE REAR BARS TOGETHER. STEP 7 OPEN THE STEERING BAG FROM BAG H1 AND THREAD A JAM NUT ON EACH 5377 KINGPIN, INSERT INTO EACH END OF THE FRONT AXLE PLATE, AND ADD A 7207 LOCKNUT ON EACH ONE. STEP 8 PRESS A 5364 STUB AXLE INTO EACH 5351 STEERING BLOCK AND RETAIN WITH A 5221 E-CLIP.
PAGE 3
STEP 11 INSTALL THE STEERING LINKAGE FROM BAG H3. INSTALL A LONG LINK IN EACH STEERING BLOCK AND TWO SHORT ONES IN THE SERVO SAVER. USE THE COLLARS AND SET SCREWS TO ATTACH THE RODS TOGETHER AFTER ALIGNING THE STEERING. STEP 12 INSTALL THE 5188 RIDE HEIGHT ADAPTORS FROM BAG L2 AND ADD THE 5452 REAR BUSHINGS. STEP 13 SNAP A DIFF BALL INTO EVERY OTHER HOLE IN THE OUTSIDE ROW OF THE GEAR. LUBE EACH ONE WITH A LITTLE THICK SILICONE OR GREASE.
PAGE 4
STEP 17 INSTALL YOUR SPEED CONTROL AND RECEIVER ON TOP OF THE RADIO TRAY WITH FOAM TAPE. MAKE SURE TO LEAVE ROOM TO USE TIE STRAPS IN A COUPLE OF THE SLOTS AT THE EDGE OF THE TRAY TO HOLD THE BATTERY PACK UNDER IT. STEP 18 IF YOUR RADIO HAS A LONG ANTENNA WIRE AND REQUIRES A SUPPORT TUBE, OBTAIN ONE FROM YOUR LOCAL HOBBY SHOP AND INSTALL THE ANTENNA TUBE ON THE INSIDE OF THE CHASSIS THRU THE SERVO PLATE WITH TWO SMALL TIE STRAPS. ROUTE YOUR ANTENNA WIRE THRU THE TUBE FROM THE BOTTOM.
PAGE 5
STEP 22 PAINT THE HOOD AND TAIL TANK PARTS AND THE SIDE PANELS AND TRIM THEM OUT AS SHOWN. DRILL THE HOLES MARKED WITH A 1/8 “ DRILL TO MOUNT THEM TO THE CHASSIS. THE TWO HOLES IN THE SIDES OF THE TAIL TANK SNAP OVER THE TWO SCREWS THAT HOLD THE REAR OF THE ROLL CAGE TO THE CHASSIS AND YOU WILL NEED TO REMOVE THE BOTTOM SCREW THAT HOLDS THE LOWER REAR BAR TO THE 1/2” SPACER TO ATTACH THE REAR OF THE TAIL TANK.
PAGE 6
STEP 26 WITH THE FRONT WING MOUNTED ON THE HOOD , YOU CAN BEND THE FRONT PORTION OF THE MOUNT TO CHANGE THE WING ANGLE FOR MORE OR LESS STEERING. STEP 27 INSTALL THE REAR WING TO THE ROLL CAGE WITH THE SCREWS THAT ATTACH THE CHASSIS BRACES . YOU CAN SLOT THE HOLES IN THE MOUNTS FOR EASY REMOVAL, BUT THE WING MAY NOT STAY ON AS WELL IN A HARD CRASH. STEP 28 PRESS THE BUSHINGS FROM BAG H3 INTO EACH SIDE OF EACH FRONT WHEEL FROM BAG L4. LUBE THE FRONT AXLES WITH LIGHT OIL AND INSTALL THE FRONT WHEELS.
PAGE 7
1525 WING FRONT WING MOUNT CUT OUT OF SHEET AND FOLD AS SHOWN USE SERVO TAPE TO ATTACH THE MOUNT TOGETHER AND TO ATTACH IT OT THE FRONT WING AND THE FRONT OF THE HOOD FRONT BEND HERE TO ADJUST FRONT WING ANGLE FOLD BACK TO STIFFEN FRONT AND REAR WINGS CUT OUT AS SHOWN TRIM LARGE AND SMALL WING AND WING MOUNTS ABOUT 1/8 INCH FROM THE BOTTOM .
PAGE 8
7030 7031 7043 7044 7045 7150 7160 7206 7207 7218 7207 7206 5364 HARDWARE 3/8 CAP SCREWS 1/2 CAP SCREWS 1/4 BTN.HD SCREWS 3/8 BTN.HD SCREWS 1/2 BTN.HD SCREWS 4-40 SET SCREWS HUB SET SCREWS 5-40 JAM NUTS 5-40 LOCK NUTS RED DIFF NUTS 5377 5351 5228 5221 REPLACEMENT PARTS 1043 BODY PARTS SET 1525 WING KIT W/SCREWS 2520 FRONT SPEC TIRES (2) 2530 REAR SPEC TIRES (2) 5060 CHASSIS, MOTOR SIDE 5061 CHASSIS, L.