30 Inch Top Fuel Dragster Instructions

ManualsBrandsRJ Speed ManualsCars & Trucks30" Wheelbase T/F Dragster Kit

RJS2006 30”WB ELECTRIC T/F

DRAGSTER KIT LESS ELECTRICS

THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT . IT IS MADE FOR STRAIGHT LINE DRAG RACING AND

MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH SPEED. IT REQUIRES A MOTOR, BAT-

TERY PACK, AND A TWO CHANNEL RADIO CONTROL UNIT WITH ONE SERVO AND AN ESC. A STANDARD

SIZE OR MINI SERVO IS GOOD FOR THE STEERING AND MOST ESC’S WILL WORK. YOU NEED TO BUY AN

ESC TO MATCH UP WITH THE MOTOR YOU ARE GOING TO USE.

YOU WILL NEED A SMALL PAIR OF PLIERS, AND A 1/4” WRENCH OR NUT DRIVER. HEX WRENCHES TO FIT

THE SOCKET HEAD SCREWS IN THE KIT ARE INCLUDED IN BAG 11. YOU WILL ALSO NEED PAINT FOR THE

BODY AND WINGS THAT IS MADE FOR LEXAN TYPE PLASTIC.

STEP 1 OPEN BAG 1 AND LOCATE BAG 11 WRENCHES.

ALIGN THE 5012 SUB FRAME OVER THE 5011 CHASSIS AND

INSTALL 4 OF THE LONGER (3/8”) SCREWS THROUGH

BOTH, ADD THE 7202 NUTS AND TIGHTEN THEM. MAKE

SURE THAT THE HOLES IN BETWEEN THE SCREWS LINE UP

WITH THE ONES IN THE CHASSIS.

MAKE SURE THESE HOLES IN THE

SUB FRAME LINE UP WITH THE

ONES IN THE CHASSIS

STEP 2 ATTACH 5 ANGLE BRACKETS TO THE 5013 CHASSIS

BRACE WITH 5 OF THE SHORT SCREWS. TIGHTEN THEM

AFTER ATTACHING IT TO THE CHASSIS ASSEMBLY.

STEP 1

STEP 3 USE THREE OF THE SHORTER SCREWS TO ATTACH

THE ANGLE BRACKETS TO THE FRONT CHASSIS SECTION AND

TWO LONGER ONES THROUGH THE SUB FRAME AND CHASSIS.

TIGHTEN ALL OF THEM.

LONGER SCREWS

STEP 3

STEP 4 BAG 2 INSERT THE THREE 1/2” LONG SCREWS UP

THROUGH THE FRONT THREE HOLES IN THE CHASSIS. SAVE

THE LONGER SCREW FOR THE BELLCRANK ASSEMBLY LATER.

ADD A 3/32 THICK SPACER ON EACH OF THE FRONT SCREWS

AND A 1/16 (THINNER ONE) ON THE REAR SCREW.

STEP 5 TRIM OUT THE FRONT WING AND DRILL THREE HOLES TO

MATCH THE FRONT AXLE PLATE MAKE SURE THAT THE BACK OF

THE WING DOES NOT EXTEND PAST THE BACK OF THE AXLE

PLATE SO IT WILL NOT INTERFERE WITH THE BELLCRANK STEER-

ING ASSEMBLY. YOU CAN PAINT THE WING BEFORE YOU INSTALL

IT WITH THE FRONT AXLE PLATE.

STEP 6 SLIDE THE FRONT AXLE PLATE AND WING ONTO THE

THREE SCREWS AND RETAIN WITH 3 NYLON NUTS.

STEP 6

STEP 4

STEP 2

STEP 5

Summary of content (6 pages)

PAGE 1
RJS2006 30”WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT . IT IS MADE FOR STRAIGHT LINE DRAG RACING AND MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH SPEED. IT REQUIRES A MOTOR, BATTERY PACK, AND A TWO CHANNEL RADIO CONTROL UNIT WITH ONE SERVO AND AN ESC. A STANDARD SIZE OR MINI SERVO IS GOOD FOR THE STEERING AND MOST ESC’S WILL WORK. YOU NEED TO BUY AN ESC TO MATCH UP WITH THE MOTOR YOU ARE GOING TO USE.
PAGE 2
STEP 7 THREAD A 7206 JAM NUT ALL THE WAY ONTO EACH 5377 KINGPIN AFTER LUBING THE THREADS WITH WD-40 OR LIGHT OIL . INSERT THEM THROUGH THE ENDS OF THE FRONT AXLE PLATE ,INSTALL A 7207 LOCKNUT ON EACH AND TIGHTEN THEM. STEP 7 STEP 8 LUBE THE KINPINS WITH SILICONE LUBE OR LIGHT GREASE AND INSTALL A 5351 STEERING BLOCK ON EACH . MAKE SURE THEY MOVE FREELY. ADD A 5228 SPRING , WASHER AND 5221 E-CLIP ON BOTH. SNAP A 5221 E-CLIP ON EACH 5363 STUB AXLE AND INSERT THEM INTO THE STEERING BLOCKS FROM THE INSIDE.
PAGE 3
STEP 14 STEP 14 INSTALL THE MOTOR MOUNT ON THE CHASSIS ASM. WITH TWO 1/4” SCREWS AND TIGHTEN ALL FOUR. STEP 15 STEP 15 PRESS THE 5169 TOP PLATE INTO THE MOTOR MOUNT AND PRESS THE LEFT AXLE MOUNT INTO THE TOP PLATE ALSO. ATTACH THE LEFT AXLE MOUNT TO THE CHASSIS AND BOTH MOUNTS TO THE TOP PLATE WITH 1/4 “ SCREWS. DO NOT OVERTIGHTEN THE ONES AT THE TOP. WING MOUNTS STEP 16 STEP 16 ATTACH THE WING MOUNTS FROM BAG D10 TO THE TOP PLATE WITH SCREWS PROVIDED.
PAGE 4
STEP 22 STEP 22 TRIM OUT THE WING AND END PLATES. PAINT THE PARTS BEFORE ASSEMBLY. ATTACH THE END PLATES WITH SCREWS OR DOUBLE BACK TAPE. BEND THE 10” WING WIRE ACCORDING TO THE TEMPLET BELOW. HOLD THE WIRE UNDER THE WING , MARK AND DRILL 1/8” HOLES ON EITHER SIDE OF BOTH WING WIRES. USE THE SMALL WIRE TIES THROUGH THE HOLES AND AROUND THE WIRE AND PULL TIGHT. YOU SHOULD BE ABLE TO SLIDE THE WING FORWARD AND BACK FOR ADJUSTMENT.
PAGE 5
014 10 5377 5363 5 9 5228 5221 3 5351 1 1067 30” ELECTRIC T/F DRAGSTER BODY (CLEAR) 1526 DRAGSTER REAR WING 1527 DRAGSTER FRONT WING (CLEAR) 2501 1.
PAGE 6
SOME CURRENTLY AVAILABLE ACCESSORIES ARE SHOWN BELOW: 5037-7” WE HAVE TWO WHEELIE BARS THAT BOLT DIRECTLY UNDER THE REAR END OF OUR DRAG KITS. OUR 5732 DIFF KIT WILL HELP YOU GET OFF THE LINE ON UNPREPARED SURFACES BY ALLOWING YOU TO ADJUST IN A LITTLE SLIP AS NECESSARY. 5314 ALUMINUM SET SCREW HUB FOR THE LEFT SIDE. 5030– 5” 5320 ALUMINUM CLAMP HUB HOLDS THE GEAR AND A 2 BOLT 1/12 SCALE WHEEL. USE THE SAME FOR THE LEFT SIDE.