1_10 Sport 3.2 Pan Car Instructions

ManualsBrandsRJ Speed ManualsCars & Trucks1/10 Sport 3.2 Pan 1/10 Dragster Kit

RJS2020 SPORT 3.2 1/10 PAN CAR KIT

LESS ELECTRICS

THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU

READ THE TEXT, LOOK AT THE PICTURES , AND THE EXPLODED VIEW DRAWING. YOU WILL NEED A SMALL

PAIR OF PLIERS, A 1/4” SOCKET OR WRENCH, AND A 7/16 SOCKET FOR THE BODY POSTS AND DIFF NUT.

HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE PROVIDED. (BAG 11)

THIS KIT REQUIRES A 540 OR 550 SIZE MOTOR, 4 OR 6 CELL BATTERY PACK, 2 CHANNEL RADIO SYSTEM

WITH 1 SERVO AND ESC AND A SERVO SAVER TO FIT THE BRAND OF RADIO YOU HAVE CHOSEN. YOU WILL

ALSO NEED PAINT FOR THE LEXAN BODY.

STEP 1 GET THE CHASSIS FROM BAG 1 AND OPEN BAG 2 . DO

NOT OPEN THE INNER BAG S2A YET. INSTALL SIX 5/8 LONG

SCREWS IN THE CHASSIS IN THE CENTER SET OF HOLES FOR

THE FRONT PLATES . ADD A JAM NUT ON EACH AND TIGHTEN.

ADD A SILICONE TUBE ON EACH ONE.

STEP 2 INSTALL THE

A-ARMS AS SHOWN

AND RETAIN WITH

LOCKNUTS.

TIGHTEN THEM UN-

TIL THE A-ARMS

TOUCH THE TUBING.

YOU CAN ADJUST

THEM LATER TO

KEEP THE TIRE

WEAR EVEN.

STEP 3 THREAD A JAM NUT (THIN ONE ) ON EACH KINGPIN,

INSERT THE KINGPIN THRU THE FRONT AXLE PLATE AND RE-

TAIN WITH A LOCKNUT.

STEP 4 SLIDE A STUB

AXLE IN EACH

STEERING BLOCK AS

SHOWN AND ADD AN

E-CLIP.

STEP 5 LUBE EACH KINGPIN WITH A SMALL AMOUNT OF

GREASE OR SILICONE LUBE. SLIDE A STEERING BLOCK ON

EACH ONE, ADD A SPRING, THEN THE STEEL WASHER, AND

RETAIN WITH AN E-CLIP ON EACH ONE.

STEP 6 OPEN BAG S3. PRESS AN OILITE BUSHING

INTO THE MOTOR MOUNT AND AXLE CARRIER AS

SHOWN. PAY ATTENTION TO THE PICTURE AND

MAKE SURE YOU PRESS THEM IN FROM THE COR-

RECT SIDE.

Summary of content (6 pages)

PAGE 1
RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES , AND THE EXPLODED VIEW DRAWING. YOU WILL NEED A SMALL PAIR OF PLIERS, A 1/4” SOCKET OR WRENCH, AND A 7/16 SOCKET FOR THE BODY POSTS AND DIFF NUT. HEX WRENCHES TO FIT THE SOCKET HEAD SCREWS ARE PROVIDED.
PAGE 2
STEP 7 ATTACH THREE ANGLE BRACKETS TO THE BOTTOM PLATE WITH 1/4” SCREWS. NOTE THE OFFSET IN THE THREE HOLES IN THE FRONT OF THE PLATE THAT WILL ATTACH IT TO THE U-PLATE. TIGHTEN THE SCREWS LATER. SMALL HOLE CLOSER THE MOTOR MOUNT SIDE STEP 8 ATTACH THE MOTOR MOUNT TO THE ANGLE BRACKETS. USE A FLAT HEAD SCREW FROM THE INSIDE AT THE FRONT AND 1/4” BUTTON HEADFROM THE OUTSIDE AT THE REAR. TIGHTEN ALL FOUR SCREWS. STEP 9 INSERT THE REAR BRACE INTO THE SLOT AT THE TOP OF THE MOTOR MOUNT.
PAGE 3
STEP 15 INSERT A 1/4” LONG SCREW THRU THE CENTER HOLE IN THE SUPPORT PLATE, THEN ADD A 3/32 PLASTIC SPACER AND THREAD THE SCREW INTO THE THREADED HOLE IN THE SIDE OF THE 1/8” (LARGER) COLLAR AND TIGHTEN LIGHTLY. STEP 16 ATTACH THE SUPPORT PLATE TO THE POSTS WITH TWO 1/4” LONG SCREWS. STEP 17 LOCATE THE SUSPENSION ROD FROM THE CHASSIS BAG AND SCREW THE PLASTIC BALL CUP ON THE THREADED END.
PAGE 4
STEP 21 OPEN BAG S6 ATTACH THE PINION GEAR SUPPLIED ON THE MOTOR YOU HAVE CHOSEN WITH THE 1/8” LONG SET SCREW. USE THE TWO SCREWS AND WASHERS TO ATTACH THE MOTOR TO THE MOTOR PLATE. SLIDE THE MOTOR BACK UNTIL THE GEARS MESH. TIGHTEN THE MOTOR LIGHTLY AND CHECK TO MAKE SURE THERE IS A SLIGHT AMOUNT OF PLAY BETWEEN THE GEARS. TURN THE GEARS , CHECK THE MESH AGAIN, AND TIGHTEN THE MOTOR SCREWS AND CHECK THE MESH AGAIN. THE GEAR WE PROVIDE WILL FIT MOST MOTORS.
PAGE 5
1 2 5022 5146 5377 5351 5228 5221 5023 5026 5 9 4 5021 7 5224 5282 5167 5730 6 5 RJS2020 SPORT 3.
PAGE 6
2010 STOCK CAR BODY WITH WING STICK-IT SERVO TAPE 2” BODY POST (2) 4” BODY POST (2) SPORT CHASSIS PLATE .093 THICK SPORT A-ARM (2) SPORT U-PLATE .093 THICK SPORT BOTTOM PLATE .093 THICK SPORT REAR BRACE .063 THICK SPORT SUPPORT PLATE .063 THICK MOTOR MOUNT PLATE .093 THICK LEFT AXLE MOUNT PLATE .093 THICK 1/8” E-CLIPS (6) #4 SPRING BUSHING (4) FRONT SUSPENSION SPRINGS (2) REAR SUSPENSION SPRINGS (2) ALUMINUM ANGLE BRACKET (4) STEERING LINKAGE SET NARROW NYLON DIFF HUB STD.