Specifications

4-4
Transceiver Receive Only Connect
To connect just the Transceiver's receiver, Key-up on the repeater's input and enter
the transceiver control number [500], followed by a 2. The CAT-1000B will connect the
transceiver's receiver to the repeater and disable the repeater's time-out timer.
Receiver activity will be repeated on the output of the repeater, however the
transceiver's transmitter will be disabled and repeater activity will not be
transmitted. Example: With a transceiver control number of 500, turn ON the
transceiver's receiver.
Key-up and enter: 5 0 0 2
Transceiver Control Number ───┴─┴─┘ └──── Command (Receiver Only ON)
Transceiver Entry Clear And RBI-1 Reset
In the Kenwood push-button mode this command will clear a partial frequency entry by
pulsing (Pin 15) on the MF-1000 Serial Interface card. In the Doug Hall mode this
command will reset the RBI-1 interface.
Key-up and enter: 5 2 5 #
└─┼─┘ └─────── Command (Entry Clear)
└─────────── Transceiver Control Prefix Number
Read Remote Base Frequency
Key-up and enter the remote base frequency prefix number followed by a 0. Un-key and
the voice will read back the current frequency including the offset and the setting of
transmitter power. Example: With a prefix number of 525, read the remote base
frequency.
Key-up and enter: 5 2 5 0
└─┼─┘ └──── Request Remote Base Frequency Read Back
└──────── Frequency load command prefix.
Load Remote Base Frequency
Key-up and enter the remote base frequency prefix, followed by the frequency, offset
and transmitter power setting. Example: With a prefix of 525, load 146.625 MHz,
minus offset, and transmitter power to HIGH.
Key-up and enter: 5 2 5 6 6 2 5 1 1
Load Prefix ──┴─┴─┘ │ │ │ │ │ └──── Transmitter Power (0=LOW, 1=HIGH)
Megahertz 1's ────────┘ │ │ │ └────── 1=Minus, 2=Simplex, 3=Plus
Kilohertz 100's ──────────┘ │ └──────── Kilohertz 1's (0 or 5)
└────────── Kilohertz 10's
Load RBI-1 Remote Base Frequency
Key-up and enter the remote base frequency prefix, followed by the band, frequency,
offset and CTCSS encoder frequency if desired. Example: With a prefix of 525, load
146.820 MHz, minus offset, and CTCSS tone 151.4 Hz.
Key-up and enter: 5 2 5 2 6 8 2 0 1
└─┼─┘ │ │ │ │ │ └─────── 1=Minus, 2=Simplex, 3=Plus
Load Prefix ────┘ │ │ │ │ └───────── Kilohertz 1's (0 or 5)
Frequency Band──────┘ │ │ └─────────── Kilohertz 10's
Megahertz 1 ──────────┘ └───────────── Kilohertz 100's
Key-up and enter: 5 2 5 5 2 4
└─┼─┘ │ └─┴──── CTCSS tone 151.4 Hz (See Chapter 8)
Load Prefix ────┘ └──────── CTCSS Tone Load Command
Load Remote Base Frequency From CAT-1000B Memory
Key-up and enter the remote base frequency prefix, followed by the memory table
position. Example: With a prefix of 525, load contents of memory 22. The voice will
say: "FREQUENCY LOAD 22."
Key-up and enter: 5 2 5 2 2
Frequency Load Prefix ───┴─┴─┘ └─┴─── Memory location