Specifications

5-8
Erase Repeater CW ID (1-2)
Key-up and send [*35X]. Un-key and the voice will say: "CONTROL OK." If the CW ID
buffer is empty and a repeater user keys-up during a voice ID, the voice ID will
continue.
Read DTMF Generator Locations (01-40)
Key-up and send [*36XX]. Un-key and the voice will read back the DTMF command stored
at that memory location. If the location is empty, the voice will say: "POSITION XX
IS CLEAR."
Program DTMF Generator Locations (01-40)
Key-up and send [*37XX] followed by the DTMF command to be stored. Un-key and the
voice will say: "CONTROL OK." Example: Store the DTMF command [523A67] at table
position 8.
Table Position──┐ ┌───────DTMF Command
*37 08 523A67
Erase DTMF Generator Locations (01-40)
Key-up and send [*38XX]. Un-key and the voice will say: "CANCEL POSITION XX."
Read Remote Base Frequency Locations (01-40)
Key-up and send [*40XX]. Un-key and the voice synthesizer will announce the
frequency, offset, and the transmitter power setting stored at memory location [XX].
If the memory location is empty, the voice will say: "ALL CLEAR".
Read Remote Base Frequency Locations RBI-1 Interface (01-40)
Key-up and send [*40XX]. Un-key and the voice will announce the frequency, offset,
and CTCSS encoder setting stored at memory [XX]. Example: The voice will say: "ONE
FORTY SIX POINT NINE FOUR MINUS CTCSS 20 ON OFF." or "ONE FORTY SIX POINT NINE FOUR
MINUS NO CTCSS." If the memory location is empty, the voice will say: "FREQUENCY
POSITION XX IS CLEAR".
Program Remote Base Frequency Locations (01-40)
Key-up and send [*41XX] followed by the frequency (4 digits), offset, and the
transmitter power setting. Un-key and the voice synthesizer will read back the
frequency, offset and transmitter power setting. Example: At table position 5, load
frequency of 146.940 MHz, minus offset, with transmitter power HIGH.
*41 05 6 9 4 0 1 1
Link Frequency │ │ │ │ │ │ │ └─Transmitter Power 0=Low, 1=High
Program Code ──┘ │ │ │ │ │ └───1=Minus,2=Simplex,3=Plus
Table Position────┘ │ │ │ └─────KHz 1's (0 or 5)
MHz 1's──────┘ │ └───────KHz 10's
└─────────KHz 100's
Program Remote Base Frequency Locations RBI-1 Interface (01-
40)
Key-up and send [*41XX] followed by the band, frequency (4 digits), offset, and CTCSS
encoder frequency. Un-key and the voice will say: "CONTROL OK." Example: At table
position 6, load frequency of 146.940 MHz, minus offset, with CTCSS encoder enabled
and set to 131.8 Hz. For Band and CTCSS tone selection see (Chapter 8).
*41 06 2 6 9 4 0 1 2 0
Link Frequency │ │ │ │ │ │ │ │ └─┴───CTCSS Encoder Frequency (01-38)
Program Code──┘ │ │ │ │ │ │ └───────1=Minus, 2=Simplex, 3=Plus
Table Position───┘ │ │ │ │ └─────────KHz 1's (0 or 5)
Frequency Band──────┘ │ │ └───────────KHz 10's
Mhz 1's─────────┘ └─────────────KHz 100's