Datasheet

ManualsBrandsRND Components ManualsLEDsTHT RGB LED 5mm B 468nm, G 520nm, R 632nm T-1 3/4

RGB LED, 5 mm

Features

• Uniform light output

• Low power consumption

• I.C. compatible

• Long life solid state reliability

• Compliance with EU REACH

• The product itself will remain within RoHS compliant Version

Abosulute Maximum Ratings at Ta 25℃

Applications

• TV set

• Monitor

• Telephone

• Computer

• Circuit board, etc

Descriptions

• The Super Bright Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diod

• The Pure Green source color devices are made with InGaN on Sapphire substrate Light Emitting Diode

• The Blue source color devices are made with InGaN on Sapphire substrate Light Emitting Diode

Notes:

a. Derate linearly as shown in derating curve.

b. Duty Factor = 10%, Frequency = 1 kHz.

Parameters Symbol Max. Unit

Power Dissipation

Red

mWPure Green 90

Blue 90

Peak Forward Current

(a)

100 mA

DC Forward Current

(b)

Red

mAPure Green 25

Blue 25

Reverse Voltage V

5 V

Operating Temperature Range T

opr

-40

℃

to +85

℃

Storage Temperature Range T

stg

-40

℃

to +100

℃

Soldering Temperature T

sld

260

℃

for 5 Seconds

Device Selection Guide

Part No. Emitting Color Lens Color

RND 135-00194

Super Bright Red

White DiffusedPure Green

Blue

Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T +41 44 944 99 11, info@distrelec.com, distrelec.com

Summary of content (8 pages)

PAGE 1
RGB LED, 5 mm Features • Uniform light output • Low power consumption • I.C.
PAGE 2
RGB LED, 5 mm Electrical Optical Characteristics at Ta 25℃ Parameters Luminous Intensity (a) Viewing Angle (b) Dominant Wavelength (c) Spectral Line Half-Width Reverse Current Iv 2θ1/2 Peak Emission Wavelength Forward Voltage Symbol λp λd △λ VF IR Emitting Color Min. Typ. Max.
PAGE 3
RGB LED, 5 mm Package Dimensions 3 (COM) 5 [0.1970] 5.85 [0.2305] 1 CATHODE GREEN 2 CATHODE BLUE 3 COMMON ANODE 4 CATHODE RED 1 2 4 5 [0.197] 0.5 [0.020] 1 4 2 0.5 [0.020] 27.00[1.063] 0.6 [0.024] 23.00[0.906] 24.00[0.945] 25.00[0.984] 1 [0.039] 8.65 [0.341] 4.9 [0.193] 3 1.27 [0.050] 3.81 [0.150] Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25 mm (.010ʺ) unless otherwise noted. 3. Protruded resin under flange is 1.00mm (.039ʺ) max.
PAGE 4
RGB LED, 5 mm Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Red: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 800 1.6 1.8 2.0 2.2 2.4 2.
PAGE 5
RGB LED, 5 mm Green: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 2.8 3.0 3.2 3.4 3.6 3.8 4.
PAGE 6
RGB LED, 5 mm Blue: Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength λp (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 2.6 2.8 3.0 3.2 3.4 3.6 3.
PAGE 7
RGB LED, 5 mm Cautions 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from RND and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. 2.
PAGE 8
RGB LED, 5 mm (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 7. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 8. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED.