User Manual
www.rnd-electronics.com
EN
Copyright information
The design of this product(including internal software) and
its acces sories is under the protection of relevant state laws.
Any vio lation of the relevant rights of our company will be
subject to legal sanctions. Users shall consciously abide by
the relevant state laws when using this products.
Disclaimer
We will take no responsibility for any personal injury or
property da ma ge caused by reasons other than the product
quality pro blem,which may include force majeure (natural
disasters,etc) or personal behavior during the operation of
this product. This manual is organized, compiled and released
by RND. according to the la test product features. We will
not be responsible for further notice of the subsequent
improvement of the product and this manual.
Essential knowledge for users
The instructions include the substance of the following:
This device is not intended for unattended children or anyone
whose physical, sensory and mental abilities do not allow
safe use. Children must be supervised to ensure that they
do not play with the appliance. Non-compliance with the
safety regulations can be life-threatening. The manufacturer
assumes no liability for damage resulting from improper use
of the device and from unauthorized modications. CAUTION:
Risk of burns. If the control unit is active there is a risk of burns
due to the soldering tool. The tool may be hot for a long time
after it is turned o • Put the soldering tool in the safety de-
posit box when it is not in use. Make sure the safety bracket
is stable • Replace the soldering tip only when it is cold.
Risk of burns due to liquid solder. Protect yourself from solder
spatters • Wear protective clothing to protect yourself from
burns. Protect your eyes with protective goggles • When
wor king with adhesive, pay attention to the manufacturer’s
warnings. WARNING: Risk of electric shock. If the control unit
is incorrectly connected, there is a risk of electric shock, which
can damage the device. If the unit is faulty, live conductors
may be exposed or the grounding conductor may not
work • Repairs must always be carried out by a trained
specialist • f the power cord is damaged or the soldering
station is faulty, discontinue use of the unit. To comply with
safety standards, the power cord must only be replaced by
an authorized technician, as special tools are required • Do
not use the unit in a damp or wet environment • Never
Soldering Iron
80W & 150W Dynamic Adjust
RND 560-00215 | RND 560-00216
User Manual
work on live parts • Prevent electrical work / Circuits ensure
that they are turned o and that the power cord has been
disconnected from the power outlet. CAUTION: Fire hazard
Covering the soldering iron or the safety holder may cause
a re. Keep other objects away from the soldering iron and
safety holder • Keep other objects away from the soldering
iron and safety holder • Keep ammable objects, liquids or
gases away from the hot soldering iron. CAUTION • Always
place the soldering iron in the original holder when not in
use • Keep the soldering tip and heating element away
from the body, clothing and ammable material during
ope ra tion the heating element is still hot for a while. Make
sure that you do not touch the soldering tip and the heating
element during this time • Do not inhale soldering vapors
to protect your health • Do not work on live parts. Repairs
may only be carried out by technicians. Only use original
spare parts. • The soldering iron can reach very high tem-
peratures. Make sure the device is turned o before servicing
/ troubleshooting “
Product overview
This product is a portable, temperature-adjustable, high-
tempe ratu re control soldering iron. The ceramic heating core
uses a three-core grounded power cable to eectively ensure
the safety of the welding operation.
Features
• Automatically sleep after 10 minutes and shut down after
20 minu tes when the product stop operating
• Products use LCD display and LED display design
• Build in PID system ,adjust temperature by button,operates
easily.
• The handle structure is ergonomically designed for comfor-
table grip.
• Display the temperature control status with a bright blue
LED.
• The heating wire and sensor are made of PTC material,
which is quick in temperature rise and precise in tempe-
rature control.
• Auto-standby, auto-shut down is available.
• Using 3 cored power cable.