Datasheet

ManualsBrandsRND Power ManualsAAAPrimary Battery, Lithium, AAA, 1.5V, Ultra Power, Pack of 4 pieces

1. Scope:

This specification is applicable to RND 305-00010 lithium/iron disulfide battery.

2. Law & Regulation Compliances:

This product complies with EU’s battery directive (2013/56/EU).

Packaging materials comply with EU’s directive on packaging materials and waste (94/62/EC)

3. General:

3.1 Type designation

IEC FR10G445

ANSI 24LF

Common FR03, AAA

3.2 Chemical system: Li/FeS

3.3 Nominal voltage: 1.5 V

3.4 Weight: Approximate 7.5 g

3.5 Dimension (mm)

The dimensions shall be in accordance with the below figures both prior to and after service output test.

Measuring equipment shall be with an accuracy ±0.05mm at least.

/ min max

Φ 9.8 10.50

A 43.50 44.50

C 4.3 -

F - 3.80

G 0.8 -

3.6 Capacity: Approximate 1200 mAh (50 mA, 24h/d, 23℃±2℃, e.v.= 0.8V)

3.7 Operation temperature : -30℃~60℃

Recommend storage temperature : Not exceed 30℃

Primary Lithium Battery

1.5 V, Pack of 4

Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T +41 44 944 99 11, info@distrelec.com, distrelec.com

Summary of content (6 pages)

PAGE 1
Primary Lithium Battery 1.5 V, Pack of 4 1. Scope: This specification is applicable to RND 305-00010 lithium/iron disulfide battery. 2. Law & Regulation Compliances: This product complies with EU’s battery directive (2013/56/EU). Packaging materials comply with EU’s directive on packaging materials and waste (94/62/EC) 3. General: 3.1 Type designation IEC ANSI Common FR10G445 24LF FR03, AAA 3.2 Chemical system: Li/FeS2 3.3 Nominal voltage: 1.5 V 3.4 Weight: Approximate 7.5 g 3.
PAGE 2
4. Electrical Characteristics Unless otherwise stated, all measurements are to be performed at a Standard Environment of 23 ± 2°C 55 ± 20% RH. All samples are normalized for 8 hours at least at the above environment prior to measurement. The digital voltmeter (DCM) is with the precision of 1mV (internal resistance not less than 1 Megohm). The load resistance of the total circuit is accurate within ±0.5% of the specified value. 4.1 Open circuit voltage and closed circuit voltage (Load resistance 50Ω, 0.
PAGE 3
5. Leakage Resistance 5.1 Overdischarge Test conditions：test battery(B1) shall be predischarged to 50 % depth of discharge. It shall then be connected in series with three undischarged additional single cell batteries(B2,B3,B4) of the same type. A resistive load R1(3.9Ω）connected in series with the assembly of batteries , R1 is 3.9 The test shall be continued for 24 h. Number of test samples：9 batteries Requirement：no explosion and no fire during this test. 5.
PAGE 4
7. Expiry Date: 10 years at 21℃ 8. Expiry Date Marking: 8.1 Unless otherwise specified, each battery will carry a manufacturing date code followed by month and year of manufacturing for domestic and manufacturing date code followed by month and year of expiry for export. (Shelf life 10 years) 9. Packaging Requirements 9.1 The total of heavy metal lead, cadmium, mercury, and hexavalent chromium concentration shall not exceed 100 ppm in Packaging materials and printing inks.
PAGE 5
Distrelec Schweiz AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T +41 44 944 99 11, info@distrelec.com, distrelec.
PAGE 6
10. Component / Information of Ingredients Chemical Nature: Lithium/iron disulfide battery APPROXIMATE PERCENT OF MATERIALS CAS NO. TOTAL WEIGHT (%) FeS2 30 12068-85-8 (iron disulfide) Li 6.1 7439-93-2 (lithium) Organic 11.5 Electrolyte Fe(iron) 27.5 MATERIALS APPROXIMATE PERCENT OF TOTAL WEIGHT (%) CAS NO. PE 4.6 9002-88-4 5.2 7429-90-5 1.0 7440-02-0 1.4 7782-42-5 Al (aluminum) Ni (nickel) 7439-89-6 Carbon Chart 1. Discharge diagram O O 1.8 1.6 1.