Owner`s manual

ManualsBrandsRoadmaster ManualsAutomobile AccessoriesSterling All Terrain

‘Flexo-Coil’ wiring kits

for tow bars without cable channel guides

164

4-wire Flexo-Coil cord with plugs and sockets

1644

4-wire Flexo-Coil cord with plugs,

sockets and socket bracket

146

6-wire Flexo-Coil cord with plugs

and sockets

1466

6-wire Flexo-Coil cord with plugs,

sockets and socket bracket

164-7

7- to 4-wire Flexo-Coil cord with plugs, sockets and socket bracket

146-7

7- to 6-wire Flexo-Coil cord with plugs, sockets and socket bracket

Straight cord wiring kits

for tow bars with cable channel guides (All-Terrain)

98164

4-wire straight cord kit

98146

6-wire straight cord kit

98164-7

7-to 4-wire straight cord kit

with plugs, socket and socket bracket

98146-7

7- to 6-wire straight cord kit

with plugs, socket and socket bracket

Bulk wiring components

1064-B

Blue 4-wire Flexo-Coil cord without plugs

1046-R

Red 6-wire Flexo-Coil cord without plugs

1064-B2 4-wire Flexo-Coil cord with two 4-way plugs

1047-B2 4-wire Flexo-Coil cord with one 4-way plug and one 7-way plug

1046-R2 6-wire Flexo-Coil cord with two 6-way plugs

1067-R2 6-wire Flexo-Coil cord with one 6-way plug and one 7-way plug

910030-2 4-wire plug

910030-1 4-wire socket

910030-8 6-wire plug

910030-7 6-wire socket

9338-77 7-wire plug

9338-70 7-wire socket

Hy-Power™ diodes

Diodes are used to tie into the towed vehicle’s brake light, running light

and turn signal wiring, and connect it to the motorhome.

Diodes permit electrical cur-

rent to flow in only one direction

— from the motorhome to the

towed vehicle’s taillights — pre-

venting electrical feedback and

the damage it can cause to both

vehicles’ electronics.

If you’re using a diode, why not

use the best? Hy-Power diodes

have a heavy-duty, powder-coated aluminum heat sink, and each diode

is protected against the elements — all components are housed inside

an epoxy-sealed, powder-coated aluminum case.

Four-pack required for most vehicles. Includes detailed wiring instruc-

tions.

790

one Hy-Power diode 792 two Hy-Power diodes

793 three Hy-Power diodes 794 four Hy-Power diodes

790-25

25-pack Hy-Power diodes (bulk pack)

Electrical

‘Brake-Lite’ Relay kit

If you’re installing a supplemental braking system, chances are you’ll

need a Brake-Lite Relay. It must be installed in the majority of towed vehi-

cles to enable the towed vehicle’s

brake lights and turn signals to illumi-

nate in tandem with the motorhome’s,

as required by law.

Comes standard with Even Brake

•

All wires and components included

•

Easy-to-follow instructions

88400

Brake-Lite Relay kit

Park Light diode

Problem — Electrical damage can occur to the towed vehicle if its

headlights are turned on while still connected to the motorhome.

Solution — Use a Park Light diode

to stop any interaction between the two

park light systems, preventing electrical

feedback and electrical damage.

Note: the Park Light diode will not re-

place Hy-Power diodes (see above).

690

Park Light diode

98146-7

1067-R2

kets

sockets and socket bracket

Flexo-Coil™ and straight power cords

Whatever electrical system you choose, you’ll need a cord to connect electricity between

the towed vehicle and the motorhome. ROADMASTER’s are the best — the wires are water-,

oil- and chemical-resistant, and the plugs are injected with silicone to prevent corrosion.

Flexo-Coil cords expand to more than eight feet and conveniently contract for storage.

1466

814