Instruction manual

Setting the clock
1. Set unit in standby mode.
2. Press & hold the “ Mem/Clk-Adj ” button (6), display will flash “24HR” press the Skip Up or Skip Down button
(23/10) to select the clock format between 12 or 24Hour. Then press the “ Mem/Clk-Adj ” button (6).
3. The first digit of “ 0:00 ” is flashing on the LCD display (17). Press Skip Up or Skip Down button (23/10) to set the
correct hour. Press “ Mem/Clk-Adj ” button (6) to store the correct hour.
4. The third & fourth digit of “ 00 ” is flashing, press the Skip Up or Skip Down button (23/10) to set the correct
minutes. Then press “ Mem/Clk-Adj ” button (6) to store the correct minute.
¾ The clock setting mode will automatically quit if no button is being pressed in a period of about 5 seconds after
pressing the “ Mem/Clk-Adj ” button.
¾ The pre-set time will be re-set completely if dis-connecting the main power supply. You are
recommended to switch the system into standby mode for convenience usage.
Listening to radio
Manual tuning
1. Switch on the unit by On/Standby button (5), then press Function button (19) to select “ Tuner ” mode.
2. Tune to the required station by pressing the Tuning Up or Down button (23/10).
3. Tuen the Volume knob (25) to the desired volume level.
Auto tuning
1. Press Function button (19) to select “ Tuner ” mode.
2. Press and hold the Tuning Up or Down button (23/10) for 1-2 seconds and then release.
3. The unit will start seeking automatically and stop until a radio station is reached.
4. Repeat step 2 & 3 until the desired radio station is being reached.
5. Press Volume knob (25) to the desired volume level.
Preset stations
You can store up to 10 radio stations in the memory
Set to tuner mode.
1. Turn to the desired radio station by “ Manual” or “ Auto ” tuning method.
2. Press and hold the Mem/Clk-Adj ” button (6) until the “ MEM ” indicator and preset station number are flash on LCD display
(17)
3. Press “ Folder / Pre-up
/down “button (9) to select the desired station memory for storage.
4. Press “ Mem/Clk-Adj ” button (6) again to confirm the setting.
5. Repeat step 1 to 4 to store other stations.
6. Now you can select the presets stations in order by pressing the “Folder / Pre-up
/down “ button (9)
¾ The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to
switch the system into standby mode for convenience usage.
¾ There are 5 seconds for program state, after 5 sec. This state would resume to normal tuner mode automatically.
¾ You can overwrite a present station by storing another frequency in its place.
FM-Stereo reception
z Press the “ St/Mono ” button (8) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly. In
particular when stereo signals are weak, it is preferable to receive the program in Mono.
z If stereo signal is being received, the stereo indicator “ ” will appear on LCD display (17) to show FM Stereo program
is now receiving.
Hints for best reception:-
- FM : the receiver has a build-in FM wire antenna (26) hanging at the rear cabinet, this wire should be totally unraveled and
extended for the best reception.
-
Playing Compact Disc
z Getting start
1. Press Function button (19) to select “ CD ” mode.
2. Press CD Tray Open/Close button (15) to open the CD tray.
3. Place a CD with the printed side facing up inside the tray & then close the CD tray by press the CD Tray Open/Close
button(15) again.
4. Focus search will performing and the LCD display (17) will show the total number of tracks & total playing time. Then, the