User Manual
Instructions and User Manual
ENGLISH
12
SPECIFICATIONS
Span 1300 mm
Length 730 mm
Weight (dry) 420 g
Flying weight 1050 g
Wing Area 16,8 dm²
Airfoil MH-43
C.G. 47 - 52 mm
Elevator ja
Rudder nein
Ailerons ja
Flaps nein
Flaps nein
Motor ja
Landing Gear nein
BOX CONTENT / NEEDED ACCESSORIES
ARF PNP
Motor not included
Robbe
ro-Power X36-1000 #5805 (built-in)
ESC not included not included (RoControl 6-60 #8711)
Folding Prop not included
Rasa CFK 9x7“ (included)
Spinner not included Alu Turbo Spinner 38mm (included)
Battery not included not included (ro-Power 4S 2200mAh)
Servo ELE not included
1x Robbe FS-166 MG #9105 (built-in)
Servo RUD / /
Servo AILE not included
2x Robbe FS-166 MG #9105 (built-in)
Servo FLAP / /
Servo cable
3x 25cm, 2x 15cm (JR) not included
2x 15cm (JR)
MULTIlock / /
MPX plugs / /
Adhesives
UHU Por, Adhesives, Activator(not included)
TX
min. 4 Channels (not included)
RX min. 4 Channels (not included)
FLIGHT INSTRUCTIONS
• Before the rst ight, observe the instructions in the „Safety Instructions“ section.
• To y in the model, you should choose a day with as little wind as possible
• A large, at meadow without obstacles (trees, fences power lines etc.) is suitable for the rst ights.
• Carry out another functional test of the drive and remote control.
• After assembling the model on the aireld, check once again that all model components such as wing,
tail units, wing mounts, engine, linkage, etc. are rmly seated.
• For the hand start a helper should be present, who can transport the model with not too little thrust
into the air.
• The start usually takes place against the wind
• Do not stall the model near the ground
• Do not initiate tight bends in the immediate vicinity of the ground.
• Check the reactions of the model to the rudder deections. If necessary, the rashes after landingto
increase or decrease the size accordingly.
• The minimum ight speed must be at an adequate safety altitude.
• Initiate the landing with sucient speed
PREFACE
Congratulations on your purchase of the new RAT.
The RAT is a high-quality FRP pylon speed model, which we have developed for experienced and ambitious
model aircraft pilots.The construction of such a model and related detailed solutions are subject to a certain
taste dependency. Therefore, the solutions of this manual are to be understood as a suggestion. The PNP
version (Plug and Play) is already very much prefabricated. The ARF version (Almost Ready to Fly) requires
model-building experience and basic technical skills in construction.
In any case, there are dierent ways and approaches to get a very good ying model. Some alternatives are
therefore discussed during the construction description, but not shown in the picture.
PLEASE READ THE INSTRUCTION VERY CAREFULLY COMPLETE BEFORE STARTING!
SAFETY INSTRUCTIONS FOR BATTERIES
• Do not immerse the battery in water or other liquids.
• Do not heat, throw into re or microwave.
• Do not short-circuit or charge with reversed polarity
• Do not expose, deform or throw the battery to pressure
• Do not solder directly on the battery
• Do not change or open the battery
• Only charge the battery with suitable chargers, never connect it directly to a power supply unit.
• Never charge or discharge the battery or charger on a ammable surface.
• Never leave the battery unattended during charging or discharging processes.
• Never charge or discharge the battery in direct sunlight or near heaters or re.
• Do not use the battery in places subject to high static discharge.
• Keep the battery away from children
• Do not associate leaked electrolyte with re, as it is highly ammable and may ignite.
• The electrolyte liquid should not get into the eyes, if it does, rinse immediately with plenty of clear
water and then see a doctor.
• Observe the safety instructions of the battery manufacturer and the charger manufacturer.