PNP-version No.: 2640 ARF-version No.: 2639 Instructions and User Manual www.robbe.
Instructions and User Manual G E N E R A L I N F O R M AT I O N • The model is designed for the components specified by us. Unless otherwise stated, servos and other electronic components are designed for standard supply voltage. Recommended cell count for Lipo batteries also refers to standard Lipos voltage of 3.7V per cell. If you use other servos, a different motor and controller, batteries, or propellers, please make sure they fit first.
Instructions and User Manual CONFORMIT Y Modellbau Lindinger GmbH hereby declares that this device complies with the essential requirements and other relevant regulations of the corresponding CE directives. The original declaration of conformity can be found on the Internet at www.robbe. com, in the detailed product view of the respective device description or on request. This product can be operated in all EU countries.
Instructions and User Manual P R E FA C E T E C H N I C A L D ATA Congratulations on your purchase of the new CALIMA. The CALIMA is a allround motorglider with a dynamic flight envelope. It can be flown within in a broad speed range. There are various ways of constructing the model, depending on your preferences. Therefore the solutions stated in this manual should only be considered as recommendations. For the most parts, the PNP (plug and play) version is already prefabricated.
Instructions and User Manual FUSELAGE ARF First install the motor on the motor mount by two M3x6 Allen screws. Make sure that the screws are tight and secure them with screw locking adhesive. A loose motor can lead to a crash and cause personal injury and damage to property! ARF 02 PNP ARF The rudder and elevator linkage are pre-built. It just has to be adjusted in its lenght. 03 04 ARF 05 07 The elevator linkage will be installed and adjusted also at 90° servo position and neutral pivot arm.
Instructions and User Manual ARF 09 ARF The battery will be fixed by a velcro loop on the front battery tray. To avoid slipping the battery, a strip of Velcro should also be glued to the wooden board under the battery. For later adjustment of the center of gravity, this can vary in its position. Only after the exact determination of the center of gravity you make a mark on the battery and the board.
Instructions and User Manual ARF ARF The linkage of the flaps is realized by a crossover connection of M2,5 parts through the surface of the wing. Therefore the rod must initially be connected to the bottom side of the flap servo and routed through the upper side of the wing in order to be connected with the flap`s rudder horn. If the servo horn is positioned in a right-angle (neutral position), the deflection of the flap should read approximately 15mm downwards.
Instructions and User Manual 20 ARF PNP Expert tip: The root ribs of the two wing parts have cutouts for MPX plugs. With a little work, you can install the servo or socket cable of the respective wing half using the MPX connector. If the adhesive tape is not sufficient, you can easily install smaller surface connectors in the root ribs.
Instructions and User Manual I N S TA L L AT I O N A N D T U N I N G P R O C E S S 22 PNP Insert both parts of the wing onto the wing connector and connect the plugs of the wing servos. Use M4 Allen socket screws to connect the wing with the fuselage. ARF 23 ARF PNP 24 Attach the wings up to the Multilock and then lock the pin with a short strong jerk. To unlock, use the red wedge and drive it between the fuselage and the wing. ARF 25 PNP 27 PNP Turn your transmitter and receiver on.
Instructions and User Manual CONTROL THROWS Function Normal Speed Elevator 12mm above/below 1-2mm above Rudder 32mm left/right Ailerons 20mm above, 14mm below Flaps Thermal Landing 3mm below 1mm above 2mm below 20mm above (or max.) 2mm above 3mm below 34mm below (or max.) ENDING Now look for a day with suitable weather conditions for the first flight. With the mentioned settings you will be spared bad surprises.
Instructions and User Manual ENGLISH F O R YO U R N O T E S 11
Modellbau Lindinger GmbH Industriestraße 10 4565 Inzersdorf im Kremstal Österreich Telefon: +43(0)7582/81313-0 Mail: info@robbe.com UID Nr.: ATU69266037 „robbe Modellsport“ ist eingetragenes Markenzeichen der Modellbau Lindinger GmbH Irrtum, Druckfehler und technische Änderungen vorbehalten. Copyright 2018 Modellbau Lindinger 2018 Kopie und Nachdruck, auch auszugsweise, nur mit schriftlicher Genehmigung.
