Building and Operating Instructions Arcus V-Tail Prop 1400 ARF No.
Building and Operating Instructions - Arcus V-Tail Prop 1400 Contents Page Contents Page Specification 2 Essential accessories 2 Recommended accessories 2 Set contents 2 Radio control system 3 Colour scheme 3 Glued joints 3 Power system 3 Installing the tail panels 4, 5 Installing the wings 5 Installing the RC system components 6 Control surface travels 6 Centre of Gravity 6 Checking the working systems, setting up the control surfaces 7 Test-flying, flying notes 7 Specification, 20 A speed controller 8
Building and Operating Instructions - Arcus V-Tail Prop 1400 No. 2593 Radio control system For this model you require a radio control system with at least four channels. We particularly recommend 2.4 GHz systems. The receiving system is powered by the speed controller’s integral BEC system. Before you check the model's working systems, set the control surfaces to neutral from the transmitter (transmitter sticks and trims central).
Building and Operating Instructions - Arcus V-Tail Prop 1400 1 Fig. 1 - The illustration shows both V-tail panels with the hard plastic joiner prior to assembly. 4 Fig. 4 - Fix the tailplane to the fuselage using the screws supplied: fit them from the underside, and at the same time slip the pushrods into the swivel barrels on the control horns. Don't tighten the retaining screws at this point! 4 2 Fig. 2 - Use Ropoxi 5-minute epoxy to glue the two V-tail panels to the hard plastic joiner.
Building and Operating Instructions - Arcus V-Tail Prop 1400 7 Fig. 7 - The illustration shows the V-tail and linkages mounted on the fuselage. 10 Fig. 10 - The picture shows the parts required to fit the wings on the fuselage. 8 Fig. 8 - Trim the aileron servo covers to fit flush in the moulded-in servo mounts. 11 Fig. 11 - Push the left-hand wing panel into the recess in the fuselage, threading the servo lead through at the same time.
Building and Operating Instructions - Arcus V-Tail Prop 1400 13 14 Fig. 13 - Connect the aileron servos to the receiver using a Y-lead. - Connect the servos and the speed controller to the receiver, referring to the RC system instructions for the correct channel assignment and connector pin configuration (the orange signal wire corresponds to the white wire in robbe-Futaba systems). Place the receiver in the fuselage and deploy the receiver aerial(s). 16 15 Fig.
Building and Operating Instructions - Arcus V-Tail Prop 1400 Checking the working systems, setting up the control surfaces - Charge the flight battery. - Switch the transmitter on, and move the throttle stick to the “motor off” end-point. - Give the flight battery a full charge, apply Velcro (hookand-loop) tape to the pack, place it in the fuselage, and connect it. Wait for the speed controller to emit a series of beeps. - Place the canopy on the fuselage; it is held in place by a magnetic latch.
Building and Operating Instructions - Arcus V-Tail Prop 1400 Specification - 20 A speed controller: Continuous current: 20 A Peak current: 25 A, (max. 10 seconds) BEC mode: Linear BEC output: 5V / 2A NiMH cell count: 5-9 LiPo cell count: 2-3 Dimensions (speed controller): 42 x 25 x 8 mm Weight: 19 g Caution: this controller is not protected against reversed polarity. Connecting a battery to the controller's terminals with reversed polarity will instantly destroy the unit.
Building and Operating Instructions - Arcus V-Tail Prop 1400 Replacement Parts list - Arcus V-Tail Prop 1400 No. 25920002 25920003 25920004 25920005 25930001 25930004 25930005 25930006 25930007 25930008 25930009 Article description Wing set V-tail set Linkages and small items BL speed controller, 20 A Fuselage Linkages and small items Spinner Motor mount Propeller, 8 x 6" Decal sheet BL motor No. 2593 Guarantee Naturally all our products are guaranteed for 24 months as required by law.
Building and Operating Instructions - Arcus V-Tail Prop 1400 No. 2593 Service Centre addresses Country Andorra Denmark Germany England France Greece Italy Netherlands / Belg. Norway Austria Sweden Switzerland Slovakian Rep. Spain Czech Rep. Company Sorteney Nordic Hobby A/S robbe-Service robbe-Schlüter UK S.A.V Messe TAG Models Hellas MC-Electronic Jan van Mouwerik Norwegian Modellers robbe-Service Minicars Hobby A.B.