Version 1.
ColorSpot 575E AT Table of contents 1. Safety instructions ........................................................................................................ 3 2.Operating determinations .............................................................................................. 4 3. Description of the device .............................................................................................. 5 4. Installation ................................................................................
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this device have to: - be qualilfied - follow the instructions of this manual CAUTION! Be careful with your operations.
2.Operating determinations This device is a moving-head spot for creating decorative effects and was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Never run the device without lamp! Do not shake the device. Avoid brute force when installing or operating the device.
3.
4. Installation 4.1Fitting the lamp DANGER ! Install the lamps with the device switched off only. Unplug from mains before ! To insert the lamp MSR 575W/2 loosen the lamp cover at the rear of head (see the drawings ) by remowing the 3 fastening screws which are marked "X,Y,Z".Carefully pull out the cover with the lamp socket assembly.If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket.
4.2 Lamp adjustment 3 adjustment screws "A,B,C" The ColorSpot 575E AT lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance. Strike the lamp,open the shutter and the iris,set the dimmer intensity onto 100% and focus the light on a flat surface (wall).Center a hot-spot(the brightest part of the image) by using the 3 adjustment screws "A,B,C".
Stat.gobo wheel: Gently bend out the gobo module to release it from the 3 distace slots and eject it from the pressing snap. Put the new gobo module back under the pressing snap and push it to the distace slots. distance slots gobo module pressing snap Rotating gobo wheel: Gently bend out the gobo module to release it from the distance slots and eject it from the pressing snap. Press the ends of the fixation ring together with an appropriate tool and remove it from the gobo holder.
prism holder prism module pressing snap fixative holes 4.5 Connection to the mains Verify the power supply settings before applying power! If you wish to change the power supply settings,see the chapter below. Connect the fixture to the mains with the enclosed power plug.If you need to install other power plug on the power cable,follow the identification table below.
4.7 Rigging the fixture DANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried out by an authorized dealer! The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope through the two apertures on the bottom of the base and over the trussing system etc. Insert the end in the carabine and tighten the fixation screw. Fixation via the omega holders 1.Bolt each clamp (1) to the omega holder (4) with M12 bolt and lock nut through the hole in the holder. 2.
4.8 DMX-512 connection/connection between fixtures The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
4.9 Ethernet connection The fixtures on a data link are connected to the Ethernet with Art-Net communication protocol.The controlling software from PC (or lighting console) has to support Art-Net protocol. Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow transfer of large amounts of DMX 512 data over a wide area using standard network technology. IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
Ethernet / DMX connection Options "Ethernet/DMX" has to be selected from "Set Ethernet Mode" menu on the first fixture (connected to the network) in the fixture chain,next fixtures have standard DMX addresses. Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of this fixture with the input of the next fixture until all fixtures are connected to the DMX chain. Caution: At the last fixture, the DMX chain has to be terminated with a terminator.
5.DMX Protocol-version 1.0 Mode/Channel 1 2 3 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 Value 1 Function Type of control 0-255 Pan Pan movement by 530° proportional 0-255 Pan fine Fine control of pan movement proportional 0-255 Tilt Tilt movement by 280° proportional 0-255 Tilt fine Fine control of tilt movement proportional Pan/Tilt speed , Pan/Tilt time Max.speed (tracking mode) step 2 3 4 5 0 P./T. speed- set Speed Mode in menu: P.t.Mo. 1-255 Speed from max. to min.
Mode/Channel 1 2 3 4 8 Value 8 0 1-127 128-129 130-255 7 7 9 9 0-255 Colour wheel 1-fine positioning Fine positioning proportional 0 14 28 42 56 70 84 98 112 128-129 Colour wheel 2 Continual Positioning In range 0 -129 DMX is possible fine colour positioning- set value on channel 10(12) Open/white Deep red Deep blue Pink Cyan Magenta Yellow 3200K correction filter UV filter White proportional proportional proportional proportional proportional proportional proportional proportional proportional
Mode/Channel 1 2 3 4 Value 11 250-255 0-255 Colour wheel 2-fine positioning Fine positioning 12 9 13 Type of control Positioning Deep red step Deep blue step Pink step Cyan step Magenta step Yellow step 3200K correction filter step UV filter step Forwards rainbow effect from fast to slow proportional No rotation step Backwards rainbow effect from slow to fast proportional Random colour selection by audio control step (Set microphone sensitivity in menu "Personality") Auto random colour selection fro
Mode/Channel 1 2 3 4 Value 244-249 250-255 12 14 0-255 13 10 15 12 0-3 4-7 8-11 12-15 16-19 20-23 24-27 28-31 32-35 36-39 40-43 44-47 48-51 52-55 56-59 60-69 70-79 80-89 90-99 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-189 190-199 200-201 202-221 222-223 224-243 244-249 250-255 14 11 16 13 0-255 0 1-127 128-129 130-255 Function Type of control Random gobo selection by audio control step (Set microphone sensitivity in menu "Personality") Auto random gobo selection from
Mode/Channel 1 2 3 4 15 Value 17 12 18 proportional Prism Open position (hole) 3-facet rotating prism Prism/gobo macros Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 Macro 7 Macro 8 Macro 9 Macro 10 Macro 11 Macro 12 Macro 13 Macro 14 Macro 15 Macro 16 step step step step step step step step step step step step step step step step step step step Prism rotation No rotation Forwards rotation from fast to slow No rotation Backwards rotation from slow to fast step proportional step proportional 0 1-1
Mode/Channel 1 2 3 4 22 16 24 Value 18 128-169 170-219 220-255 Zoom Zoom without focus corection Zoom 15° Zoom 18° Zoom 22° Zoom with focus corection *** Zoom 15° Zoom 18° Zoom 22° 0-255 Focus Coarse focus 0-255 Focus fine Fine focus adjustment 0-39 40-79 80-127 23 17 24 25 25 19 26 18 27 20 192-223 224-255 19 28 21 0-255 27 29 0-255 * ** *** Type of control step step step step step step proportional Shutter,Strobe 0-31 32-63 64-95 96-127 128-143 144-159 160-191 26 Function S
6. Controller mode The fixtures are individually addressed on a data link and connected to the controller.The fixtures respond to the DMX signal from the controller. 6.1 DMX addressing There are 512 available channels on DMX link.Every fixture on DMX link must have a DMX start address, which is defined as the first channel from which the fixture will respond to the controller.
Focus,Zoom Motorized focus enables the beam to be focused anywhere on stage at different beam angles 15°,18°,22°,provided by the special zoom. Dimmer/Shutter/Strobe Smooth 0 - 100 % dimming is provided by the combined mechanical dimmer/shutter unit. This unit may also be used for strobe effect (1 - 10 flashes per second) Fans By the Control Board using the "Fan Modes" function you can choose the 2 types of the fan speed operating modes.
8.Control menu map Default settings=Bold print Default settings=Bold print Fixture Address DMX Address 001 : 512 Ethernet Settings Set Ethernet Mode Disable Ethernet Ethernet Ethernet/DMX Set IP Address Default IP Address Custom IP Address Set ArtNet Universe (0 -255) Fixture information Power On Time Total Hours Resetable Hours Lamp On Time Total Hours Resetable Hours Lamp Strikes Total Hours Resetable Hours Fixture Temperatures Current Board Temp. [°C] Head Temp.[°C] Maximum Nonresetable Board Temp.
Personality User Mode User A Settings User B Settings User C Settings DMX Presetting Mode 1 Ch.1 Pan : Ch.24 Dimmer Fine Set Active Mode 2 Ch.1 Pan : Ch.19 Dimmer Set Active Mode 3 Ch.1 Pan : Ch.29 Dimmer Fine Set Active Mode 4 Ch.1 Pan : Ch.21 Dimmer Fine Set Active Pan Reverse (On,Off) Tilt Reverse (On,Off) Lamp Presetting Lamp On/Power On (On,Off) Lamp Off via DMX (On,Off) Lamp On if DMX Present (On,Off) Lamp Off if not DMX (On,Off) Lamp Ignition delay (0..1..
Lamp On/Off (On,Off) Test sequences Mode 1 Pan (0-255) Tilt (0-255) Zoom (0-255) Focus (0-255) Run Test Program Mode 2 Run Test Program Manual Mode Presetted Effect Control Pan (Position 1,...,Position 6) : Dimmer (Position 1,...
Effect Adjustment DMX Values Pan (0-255) : Dimmer fine (0-255) Calibrate Values Pan (0-225) : Dimmer (0-255) Save and Reset 26
9. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address,read the number of the lamp or unit hours, switch On and Off the lamp, run test, make a reset and also use many functions for setting fixture behaviour. Control elements on the control board: [RNS] encoder wheel-moves between menu items on the the same level, scrolls between values.
8.2 Fixture informations Use this menu to read an useful information about the fixture. Power On Time ---Select this submenu to read the number of operation hours. Total Hours --- The function shows the total number of the operation hours since the ColorSpot 575E AT has been fabricated. Resetable Hours --- The function shows the number of the operation hours that the ColorSpot 575E AT has been powered on since the counter was last reset.In order to reset this counter to 0,press [ENTER] twice.
9.3 Personality Use this menu to to modify ColorSpot 575E AT operating behavior. User mode --- ColorSpot 575E AT allows you to recall up to 3 user settings.After switching the fixture on for the first time, the User A settings are active.All changes made in "Personality" menu ,"Fixture Address" menu and Music Trigger and Presetting Playback functions from "Stand-alone setting" menu are saved to the User A settings.
Fan Modes --- By using this function you can choose 2 types of the fan speed operating modes. Auto Cooling --- The fans automatically raise their speed in order to control inside temperature of the lighting, if the temperature inside increases about certain level (the low fan speed reduces the cooling of the lighting). This cycle can repeat several times until the temperature inside is on a suitable level. High Cooling --- The cooling fans work on max. speed (max. cooling).
Program 3 --- The option will start created program No. 3 Note:If the fixture operates in the controller mode ( DMX controller is connected) and any program from this menu is selected ,in this case the fixture will not respond to the DMX controller after switching on and will play selected program. Playing program --- Select this menu to run a bilt-in program or the 3 freely-programmable programs in a loop. Test Program In Loop --- The option starts built-in test program.
Pan/Tilt --- This function resets pan and tilt. Colour System --- This function resets colour wheels. Gobo System --- This function resets static and rotating gobo wheels. Dimmer/Strobe --- This function resets dimmer/strobe module. Focus/Zoom/Frost --- This function resets focus,zoom and frost. Iris/Prism --- This function resets iris and rot.prism. 9.9 Special functions Use this menu for special services like adjusting lamp or adjusting effects.
11. RDM This fixture allows RDM operation.RDM (Remote Device Management) is a bi-directional communications protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non-RDM equipment.
Caution: The message is disabled if the lamp light sensor (function "Lamp Sensor"in menu Personality) is switched Off. Lamp Error The ignition of the lamp is seven times unsuccessful (the "Active Lamp Timer" message appeared six times before), and the display shows "Lamp Error", meaning that the lamp could be damaged or even missed or there could be a failure on the ignitor or ballast. Please place or replace the lamp and contact your dealer if the situation was not caused by the lamp.
Tilt Error 1 (Tilt Error 2) The messages will appear after the reset of the head if the head is not located in the default position. 13. Technical specifications Power supply: Voltage:.................................100/120/208/230/240V AC, 50/60Hz ~ Live Fuse:...............................T 6.3A@230V, T 10A@120V Neutral Fuse:..........................T 6.3A@230V,T 10A@120V Power consumption:.................
Colours: Colour wheel 1: - 9 dichroic filters + open Colour wheel 2: - 8 replaceable 'SLOT&LOCK' dichroic filters (including 3200 K and UV filter) + open Static gobo wheel: - 9 replaceable 'SLOT&LOCK' metal gobos plus an open position,outside diameter=26.9mm,image diameter=22.5mm, aluminium,thickness=0.5mm Rotating gobo wheel: - 6 dichroic glass gobos and one glass gobo rotating in both directions at different speeds - Gobo indexing - Rotating gobo-wheel cont.
-Max.Pan speed 157.27°/sec. -Max.Tilt speed 108.95°/sec. -Pan/tilt control accuracy: 0.00415°/0.
14. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
