Version 1.
ColorWash 700E AT Table of contents 1. Safety instructions.......................................................................................................... 3 2. Operating determinations............................................................................................... 4 3. Description of the device................................................................................................ 5 4. Installation..............................................................................
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this device have to: - be qualilfied - follow the instructions of this manual CAUTION! Be careful with your operations.
2.Operating determinations This device is a moving-head for creating decorative effects and was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Never run the device without lamp! Do not shake the device. Avoid brute force when installing or operating the device.
3. Description of the device 1 - Front lens 2 - Pan lock 3 - Base 4 - Handle 5 - Head yoke 6 - Tilt unlock button (green) 7 - Tilt lock button (red) 8 - Moving head The head should be locked for transportation - the tilt lock button (7) is pushed and the pan lock/unlock lever (2) is in locked position.To unlock the head, press the tilt unlock button (6) and move the pan lock/unlock lever (2) to unlocked position.
4. Installation 4.1 Connection to the mains For protection from electric shock,the fixture must be earthed! The ColorWash 700E AT is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz AC power source from 100-240 Volts. For use with 100-130 V supplies,the both main 6.3 A fuses has to be exchanged for 10 A fuses which are enclosed in the packing. To install the 10 A fuses: 1. Disconect the fixture from AC power. 2.
6. Align the new lamp (see instructions below) 7. Reset „Lamp On Time” and „Lamp Strikes” counters in „Fixture information” menu. Do not operate this fixture with open lamp cover! 4.3 Lamp adjustment The lamp holder is aligned at the factory.Due to differences between lamps, fine adjustment may improve light performance: To align the lamp: 1. Switch on the fixture and after reset turn on the lamp. 2.
4.5 Changing the front lens The ColorWash 700E AT is supplied with the front Fresnel lens installed as standard. If you wish to install a front wide-angle lens (optional),follow the instructions: Switch the device off before changing the lens.Be careful.Front lens is heavy! Changing the front Fresnel lens: 1.Remove the front lens using a flathead screwdriver to unlock the four quarter-turn screws. 2.Unscrew the safety cabel from the lens 3.Screw up the safety cable to the wide-angle lens. 4.
4.7 Rigging the fixture DANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried out by an authorized dealer! The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope through the two apertures on the bottom of the base and over the trussing system etc. Insert the end in the carabine and tighten the fixation screw. Fixation via the omega holders 1.Bolt each clamp (1) to the omega holder (4) with M12 bolt and lock nut through the hole in the holder. 2.
4.8 DMX-512 connection The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
4.9 Ethernet connection The fixtures on a data link are connected to the Ethernet with Art-Net communication protocol.The controlling software from PC (or lighting console) has to support Art-Net protocol. Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow transfer of large amounts of DMX 512 data over a wide area using standard network technology. IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
Ethernet / DMX operation Options “Ethernet/DMX” has to be selected from “Set Ethernet Mode” menu on the first fixture (connected to the network) in the fixture chain,next fixtures have standard DMX addresses. Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of this fixture with the input of the next fixture until all fixtures are connected to the DMX chain. Caution: At the last fixture, the DMX chain has to be terminated with a terminator.
5.ColorWash 700E AT - DMX Protocol-version 1.3 Mode/Channel 5 6 Value Function Type of control 1 2 3 4 1 1 1 1 18 16 0 - 255 Pan Pan movement by 530° proportional 2 2 2 2 19 17 0 - 255 Pan Fine Fine control of pan movement proportional 3 3 3 3 20 18 0 - 255 Tilt Tilt movement by 280° proportional 4 4 4 4 21 19 0 - 255 Tilt fine Fine control of tilt movement proportional 0 5 5 5 5 22 20 1 - 255 1 - 255 - - 6 - - 6 7 8 8 - - - - step Speed from max.
Mode/Channel 1 2 3 4 5 6 Value 0 16 32 48 64 80 96 112 128-129 7 7 9 9 12 7 130-137 138-145 146-153 154-163 164-171 172-181 182-189 190 - 215 216 - 217 218 - 243 244 - 249 250 - 255 8 - 10 9 8 11 10 10 9 - 13 - 4 3 12 11 6 4 11 10 13 12 8 5 12 11 14 13 10 6 13 12 15 14 - - 14 13 16 15 15 - Function Colour wheel Continual positioning Open/white Deep red Deep blue Orange Green Light red Amber UV filter White Positioning Deep red Deep blue Orange Green Light red Amber UV
Mode/Channel 1 2 3 4 5 14 13 16 15 15 6 - Value Function 152-159 160-167 168-175 176-183 184-191 192-199 200 - 207 208 - 215 216 - 223 224 - 231 232 - 239 240 - 243 244 - 249 Macro 19 Macro 20 Macro 21 Macro 22 Macro 23 Macro 24 Macro 25 Macro 26 Macro 27 Macro 28 Macro 29 Macro 30 - Random rainbow effect from fast to slow Random macro selection by audio control (Set microphone sensitivity in menu "PErsonality") 250 - 255 Auto random macro selection from fast to slow Effect wheel Full beam B
Mode/Channel Value Function 1 2 3 4 5 6 - - - - - 14 No function - - - - - 15 No function * 10s=default time delay,this value can be changed by "Lamp Low Power Delay" menu 17 Type of control
6. Controller mode The fixtures are individually addressed on a data link and connected to the controller.The fixtures respond to the DMX signal from the controller. 6.1 DMX addressing The control panel on the front panel of the fixture allows you to assign the DMX fixture address, which is defined as the first channel from which the ColorWash 700E AT will respond to the controller.
7.
Personality User Mode User A Settings User B Settings User C Settings DMX Presetting Mode 1 Ch.1 Pan : Ch.22 Dimmer Fine Set Active Mode 2 Ch.1 Pan : Ch.18 Dimmer Set Active Mode 3 Ch.1 Pan : Ch.24 Dimmer Fine Set Active Mode 4 Ch.1 Pan : Ch.20 Dimmer Set Active Mode 5 Ch.1 Shutter/Strobe : Ch.
IR Sensor (On,Off) Init Effect Positions Pan (0-225) : Dimmer (0-255) Dimmer fine (0-255) Save Temperature Unit (°C,°F) Default Setting Lamp On/Off (On,Off) Test sequences Mode 1 Mode 2 Pan (0-255) Tilt (0-255) Zoom (0-255) Run Test Program Manual Mode Preset Effect Control Pan (Position 1,...,Position 7) : Dimmer (Position 1,...
Reset functions Reset All Pan/Tilt : Dimmer/Strobe Special functions Lamp Adjustment Pan (0-255) Tilt (0-255) Zoom (0-255) Effect Adjustment DMX Values Calibrate Values Pan (0-255) : Dimmer fine (0-255) Colour Wheel (0-225) : Mech.
8. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address, read the number of the lamp or unit hours, switch On and Off the lamp, run test, make a reset and also use many functions for setting fixture behaviour. Control elements on the control board: [RNS] encoder wheel-moves between menu items on the the same level, scrolls between values.
Resetable Hours - The function shows the number of the operation hours with the lamp on that the ColorWash 700E AT has been powered on since the counter was last reset. In order to reset this counter to 0, press [ENTER] twice. Lamp Strikes - Select this submenu to read the total number of the lamp strikes. Total Hours - The function shows the total number of the lamp strikes since the ColorWash 700E AT has been fabricated.
8.3 Personality Use this menu to to modify ColorWash 700E AT operating behavior. User mode --- ColorWash 700E AT allows you to recall up to 3 user settings.After switching the fixture on for the first time, the User A settings is active.All changes made in “Personality” menu ,”Fixture Address” menu and Music Trigger and Presetting Playback functions from “Stand-alone setting” menu are saved to the User A settings.
Microphone Sensitivity --- Select this function to adjust the microphone sensitivity from 1(maximum) to 20(minimum).If the sensitivity is correctly adjusted,the mark will appear (blinking in the bass beat.) Fan Modes --- By using this function you can choose 2 types of the fan speed operating modes.
8.7 Stand-alone setting Use this menu to set options for stand-alone mode as a selection of the playing program,programming and modifying current programs. Music Trigger --- Select this function to enable the sound control of the running programs via the built-in microphone. Presetting Playback --- This function allows you to select the program which will be played in the stand-alone mode after switching the fixture on.Selected program will be played continuously in a loop.
Lamp Adjustment --- This function can be used when you make the fine adjustment of the lamp.If you select this function,all effects will be canceled,shutter will be opened and the dimmer intensity will be set onto 100%.By using the options “PAn, Tilt, Zoom” you can aim the light at a flat surface (wall) and perform the fine lamp adjustment. Effect Adjustment --- By this function you can calibrate and adjust the effects to their standard/right positions.
If you do not want to continue in software update, you have to switch off and on the fixture to leave this option!) 3.It is recommended that you exit all programs before running this Software Uploader. 4.Start the Software Uploader program. Select desired COM and then click Connect button. If the conection is OK, click Start Uploading button to start uploading. It will take several minutes to perform software update.
Parameter ID Discovery command SET command GET command DISPLAY_LEVEL * * PAN_INVERT * * TILT_INVERT * * DEVICE_RESET * DMX_PERSONALITY * * DMX_PERSONALITY_DESCRIPTION * STATUS_MESSAGES * STATUS_ID_DESCRIPTION * LAMP_STATE LAMP_ON_MODE DEVICE_HOURS LAMP_HOURS 1 * * * * * 2 * 2 LAMP_STRIKES * 2 ...
Supply Frequency Error This message will appear if the frequency of the main is not standard 50 or 60 Hz.This message can appear as a result of the interference during the lamp starting (if the lamp or igniter is old) or as a result of the interference by neighbouring devices. In these cases the message does not affect the fixture operating! Temper.
Strobe 1 Error 1 (Strobe 1 Error 2 ) The messsages will appear after the reset of the dimmer/strobe module if the strobe lamella1 is not located in the default position. Strobe 2 Error 1 (Strobe 2 Error 2 ) The messsages will appear after the reset of the dimmer/strobe module if the strobe lamella 2 is not located in the default position. 12. Technical specifications Electrical: Power supply:.........................electronic auto-ranging Input voltage range:...............
-Ethernet operation (Art-Net communication protocol) -Stand-alone operation -Digital serial input DMX-512 -Ready for RDM (Remote Device Management) protocol -Protocol USITT DMX 512 -6 DMX modes (18,20,21,23,22,24 control channels) Pan/Tilt -Pan movement range 530° -Tilt movement range 280° -16 bit movement resolution -Automatic Pan / Tilt position correction -Remotely controllable speed of pan/tilt movement for easy programming -Movement control:tracking and vector
Weight (net): 30.4 kg Dimensions(mm) Dimensions of the fixture: Dimensions of top hats: Accessories - Omega holder (2 pieces)................................No.99010420 Optional Accessories - Module of front wide-angle lens ......................No. 99010879 - Flash cable RS232/DMX..................................No.13050624 - Top hat standard 45 ........................................No.10980044 - Top hat long 70 ...............................................No.
13. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
Replacing the air filter in the fixture base 1)Disconect the fixture from power. 2)Remove side fans cover by loosening the 4 quarter-turn fasteners. 3)Remove the air filter from the cover. 4)Clean or replace the air filter. 5)Place the filter on the cover and put this cover back. 6)Reset the elapsed time counter in menu Fixture information (Fixture Information--->Air Filters---> Elapsed Time. air filter cover quarter-turn fasteners Replacing the fuse Before replacing the fuse, unplug mains lead.
