Version 1.
Robin Actor 3 ST Smart White Table of contents 1. Safety instructions.......................................................................................................... 3 2. Fixture exterior view ...................................................................................................... 5 3. Installation....................................................................................................................... 6 3.1 Connection to the mains........................................
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR ROBIN Actor 3 ST ! Save it for future reference. This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
or dust. Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of the device and to protect it from overheating. Do not block the LEDs array with any object when the fixture is under operation. The openings should never be covered with cloth or other materials, and never must be blocked. This fixture should not be placed in a built-in installation unless proper ventilation is provided.
2.
3. Installation Fixtures must be installed by a Qualified electrician in accordance with all national and local electrical and construction codes and regulation. 3.1 Connection to the mains For protection from electric shock, the fixture must be earthed! The Robin Actor 3 ST is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC power source from 100-240 Volts.
3.2 Installing the top hat Switch off the fixture before top hat installation 1.Unscrew the four fastening screws (3) which securing flange (4) to the head (5) and install new flange. Keep its right position- the cutouts (A) in the flange must look towards the arms. Original flange New flange 2.Place the top hat (1) on the head (5), press locks (2) and turn the top hat counter-clockwise until it snap into slots (B) in the flange.
3.3 Rigging the fixture The overhead installation must always be secured with a secondary safety attachment, e.g. an appropriate safety rope. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails. When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden.
For securing the fixture to the truss install a safety wire that can hold at least 10 times the weight of the fixture. Use only a safety wire with screw-on snap-hook. Thread the snap-hook through two apertures in the fixture base and the wire around the truss as shown on the picture below.
3.4 DMX-512 connection The fixture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair cable designed for RS-485 and 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
4. Control menu map Default settings=Bold print Level 1 Level 2 Level 3 DMXA Set DMXA 001-255 Info POn Time Level 4 Level 5 Zoom Vir C Dimm MENU Total Reset DMX In Pover 0-255 : Dimm F Temp 0-255 Current Highest High Res Sw Ver IC-1 IC-2 IC-3 Pers DMX Pres Mode 1 : Mode 6 DMX In Wired Wireless Display Turn On/Off T On, Off Contrast 0-100% Backlight 0-100% Mic Sens 0...10...
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Prog 1 Step 1 Pan Prog 2 : : Prog 3 Step 40 F.Tim 0-25.5 S.Tim 0-25.
5. Robin Actor 3 ST Smart White - DMX chart Version 1.0 Mode/Channel 1 - 2 - 3 - 4 - 5 - 6 1 2 3 4 5 Value No function No function No function No function 10-14 15-19 1 1 1 1 6 Type of control No function 0-9 1 Function 20-169 170 - 179 180 - 189 190 - 199 200 - 209 210 - 239 240 241 - 255 Special functions Reserved To activate following function, stop in DMX value for at least 3sec. and shutter must be closed at least 3sec. (Shutter channel 17/9/6/4/4/22 must be at range of 0-31DMX).
Mode/Channel Function Type of control 2 3 4 5 11 - - - 17 16 0-255 Warm white fine (16 bit) - zone 3 Fine warm white LEDs saturation control proportional 12 - - - 18 17 0-255 Cool white (8 bit) - zone 3 Cool white LEDs saturation control (0-100%) proportional 13 - - - 19 18 0-255 Cool white fine (16 bit) - zone 3 Fine cool white LEDs saturation control proportional 7 0 1-2 3-4 5-6 7-8 9-10 11-12 13-14 15-16 17-247 14 6 4 2 6 Value 1 19 248 249 250 251 252 253 245 255
5.
6. Control menu The Robin Actor 3 ST is equipped with 2-line LCD display which allows to set the fixture´s behaviour according to your needs, obtain information on its operation, test its various parts and lastly program it, if it has to be used in a stand-alone mode. Control panel: [ESCAPE] button used to leave the menu without saving changes. [NEXT] , [PREV] buttons for moving between menu items and for value adjusting.
In order to reset this counter to 0, press and hold both [NEXT] and [PREV] buttons and the [Enter] button at the same time. DMX In - DMX readout. The menu is used to read DMX values of each channel received by the fixture. Temp - Temperature. The menu shows temperature in the LED module. Current - A current temperature of the LED module. Highest - A maximum temperature of the the LED module since the fixture has been fabricated.
6.9 Stand-alone (St Alone) Music T - Music trigger. Select this function to enable the sound control of the running program via the built-in microphone. Auto Run - Presetting playback. This function allows you to select the program which will be played in the stand-alone mode after switching the fixture on. Selected program will be played continuously in a loop. Off - The option disables „Auto Run” function. Test - The option will start built-in test program.
Note 1: Software update should execute a qualified person. If you lack qualification, do not attempt the update yourself and ask for help your ROBE distributor. Note 2: DMX address, , programs 1-3 and all items in the menu "Pers" will be set to their default (factory) values. To update software in the fixture: I. Installation of the DMX Software Uploader. 1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz. 2. Make a new directory ( e.g.
SENSOR_DEFINITION * SENSOR_VALUE * DISPLAY_INVERT * * DISPLAY_LEVEL * * DEVICE_RESET * DMX_PERSONALITY * * DMX_PERSONALITY_DESCRIPTION * STATUS_MESSAGES * STATUS_ID_DESCRIPTION * DEVICE_HOURS * PARAMETER_DESCRIPTION * 8. Wireless DMX operation The wireless version of the Actor 3 ST is equipped with the Lumen Radio CRMX module and antenna for receiving DMX signal. CRMX module operates on the 2.4 GHz band.
10. Technical Specifications Electrical Power supply:.........................electronic auto-ranging Input voltage range:............... supply 100-240V, 50-60Hz Fuse:.......................................T 3.15A/250V ~ Power consumption *:........ 200W @230V,power factor=0,96 *Allow for a deviation of +/-10% Optic Light source: 19 Osram Ostar ww/cw multichips 3 zones with individual colour control of each Min LED life expectancy: 20.
Temperatures Maximum ambient temperature : 45° C Maximum housing temperature : 75° C Distances Min. distance from flammable surfaces: 0.4 m Min. distance to lighted object: 1 m Total heat dissipation 682 BTU/h (calculated) Weight (net) 5.2 kg (without floor stand) 6.3 kg (with floor stand) Dimensions (mm) Accessories Omega holder (P/N 99010420)...........................................1 piece Floor stand (P/N 99013521)............................................
11. Maintenance and cleaning DANGER ! Disconnect from the mains before starting any maintenance work A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances should alcohol or solvents be used! Never use alcohol or solvents for cleaning lenses in the fixture! Use wet cloth only. It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture.
12.