Installation Instructions

ManualsBrandsRobern ManualsBathroom FurnitureFlat Mirrored Door

This instrucon sheet contains informaon

on how to install the PL Series cabinets. This

series comes in many sizes. Refer to specic

model numbers for dimensions. These

cabinets are modular and can be mounted

with lighng.

Read the specic instrucon for how your

cabinet(s) will be mounted. The cabinets can

be surface mounted or recess mounted .

Save these instrucons for future use and

reference. An improper installaon voids

the warranty. Installed cabinets cannot be

returned.

If you experience any problems with your

cabinet, contact your dealer or Robern di-

rectly.

Limited Warranty — One Year Term

PL SERIES with Safeseal™ Gasket

SÉRIES PL

SERIE PL

PL/PLW

Robern, Inc.

701 N. Wilson Ave.

Bristol, PA 19007 U.S.A.

1.800.877.2376

INSTALLATION / INSTALLATION / INSTALACIÓN

15¼, 19¼, 23¼”

387 / 489 / 591mm

15¼, 19¼, 23¼”

387 / 489 / 591mm

30, 36”

762 / 915mm

30”

762mm

30, 393⁄8”

762 / 1000mm

34”

864mm

45⁄8”

117mm

45⁄8”

117mm

Ce feuillet d’instrucons conent de

l’informaon sur comment installer les

armoires des Séries PL. Les armoires de

cee Série sont disponibles en plusieurs

tailles. Veuillez vous référer au numéro de

modèle spécique pour les dimensions. Ces

armoires sont modulaires et peuvent être

installées avec de l’éclairage.

Lire les instrucons spéciques pour le

montage de votre armoire. Ces armoires

peuvent être montées en surface ou

encastrées.

Conservez ces instrucons pour référence et

ulisaon future. Une mauvaise installaon

annule la garane. Les armoires installées

ne peuvent pas être retournées.

Si vous éprouvez de la diculté avec

votre armoire, veuillez contacter soit

votre marchand ou contactez directement

Robern.

Garane limitée — d’une durée d’un an

Esta hoja de instrucciones conene

información sobre cómo instalar los gabinetes

de la Serie PL. Esta serie viene en diversos

tamaños. Consulte los números especícos

de modelo para ver las dimensiones. Estos

gabinetes son modulares y pueden ser

montados con luces.

Lea las instrucciones especícas para la

manera en la cual se debe(n) montar el/los

gabinete(s). Los gabinetes pueden montarse

en supercie y empotrados.

Guarde estas instrucciones para uso y

referencia futura. La instalación inadecuada

invalida la garana. Los gabinetes instalados

no podrán devolverse.

Si usted ene algún problema con su

gabinete, póngase en contacto con su

distribuidor o directamente con Robern.

Garana Limitada – Plazo de Un Año

Summary of content (24 pages)

PAGE 1
30” 762mm PL SERIES with Safeseal™ Gasket SÉRIES PL SERIE PL 30, 36” 762 / 915mm 45⁄8” 117mm 15¼, 19¼, 23¼” 387 / 489 / 591mm INSTALLATION / INSTALLATION / INSTALACIÓN This instruction sheet contains information on how to install the PL Series cabinets. This series comes in many sizes. Refer to specific model numbers for dimensions. These cabinets are modular and can be mounted with lighting. Read the specific instruction for how your cabinet(s) will be mounted.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed, including the following: DANGER - Read all instructions before using this cabinet. WARNING - To reduce the risk of burns, ﬁre, electric shock, or injury to persons: Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening.
PAGE 3
CONTENT / contenu / contenido page [1] NOTES page [1] REMARQUES página [1] NOTAS [3] PARTS [3] PIÈCES [3] PARTeS [4] MODEL NUMBERS [4] des numéros de modèles [4] los números de modelo [5] DIMENSIONS [5] DIMENSIONS [5] DIMENSIONES [6] ELECTRIC OPTION [6] OPTION ÉLECTRIQUE [6] OPCIÓN ELÉCTRICA [9] RECESSED MOUNTING [9] MONTAGE ENCASTRÉ [9] MONTAJE EMPOTRADO [11] SURFACE MOUNTING [15] GANGING CABINETS [11] MONTAGE EN SURFACE [15] AMALGAME D’ARMOIRES [15] GABINETES ACOPLADOS [11] MONTAJE EN
PAGE 4
PARTS / PIÈCES / PARTES 2-2 Z mounting bar barre de montage en Z barra de montaje en “Z” provided with top mounted light fixtures fournis par les feux supérieur en option proporcionada con las luces de arriba opcional 3-Z Clip 3-clip en Z 3-sujetador en “Z” [R027011HM] PLGKIT OPTIONAL* OPTIONNEL* OPCIONAL* 3-4 Glass Shelf 3-4 tablette en verre 3-4 estante de vidrio PLSK30D4 PLSK40D4 OPTIONAL* OPTIONNEL* OPCIONAL* 8-[SS202] 8-[SS241] 8-[SS676] 18-[SS202] 18-[SS241] 3” X 3 3/4” MIRRORS 18-[SS676] 4-
PAGE 5
MODEL NUMBERS / NUMÉROS DE MODÈLES / NÚMEROS DE MODELO 1-1 CABINET INTERIOR&FRAME/ INTÉRIEUR ET CÂDRE DE L’ARMOIRE/ INTERIOR Y MARCO DEL GABINETE BBM= Black Interior, Bead Frame, Mahogany Intérieur noir, cadre mouluré, acajou Interior negro, marco adornado, caoba WBB= White Interior, Bead Frame, Biscuit Intérieur blanc, cadre mouluré, biscuit Interior blanco, marco adornado, bizcocho WWW= White Interior, Bead Frame, White Intérieur blanc, cadre mouluré, blanc Interior blanco, marco adornado, blanco BHG=
PAGE 6
DIMENSIONS / DIMENSIONS / DIMENSIONES Determine overall cabinet and lighting fixture dimensions. If recessing cabinet, determine rough-in dimensions. See chart for specific model dimensions. 1-1 Déterminez les dimensions globales de l’armoire et de l’éclairage. Pour une armoire encastrée, déterminer les dimensions brutes. Voir le tableau pour les dimensions spécifiques selon le modèle. Determine overall cabinet and lighting fixture dimensions. If recessing cabinet, determine rough-in dimensions.
PAGE 7
ELECTRIC OPTION / OPTION ÉLECTRIQUE / OPCIÓN ELÉCTRICA 1-2 If an electrical option is provided, all wiring should be done by a qualified licensed electrician. Si une option électrique est fournie, tout le filage doit être fait par un électricien qualifié et licencié. Si se proporciona una opción eléctrica, todo el cableado debe ser realizado por un electricista calificado. WARNING: To reduce the risk of electrical shock, shut off power before wiring the cabinet.
PAGE 8
ELECTRIC OPTION / OPTION ÉLECTRIQUE / OPCIÓN ELÉCTRICA 1. If cabinet has an electrical option, remove the access screws in bottom of the outlet shelf. Remove outlet shelf for access to electrical connections. 2. Feed electric wire through access hole and in back of cabinet. 3. Make connections. 4a-b. Replace outlet shelf, making sure not to crimp or pinch wires and connections. Replace two access screws on outlet shelf. 1 2-2 1.
PAGE 9
RECESS MOUNTING / MONTAGE ENCASTRÉ / MONTAJE EMPOTRADO These instructions are for recess mounting your cabinet. Remove and store door with corner guards prior to installation. 1. Make rough opening and frame on all sides. Find the specific model dimensions to make rough opening (page 6). Make sure cabinet door is at least 1” (25mm) clearance to the top of the faucet and at least 1” from the ceiling. 2. Electrical Option Cabinets: Provide a separate electrical connection for electrical options and lighting.
PAGE 10
RECESS MOUNTING / MONTAGE ENCASTRÉ / MONTAJE EMPOTRADO 3. Place cabinet in rough-in and make sure cabinet is plumb and level. 3. Place cabinet in rough-in and make sure cabinet is plumb and level. 4. Install a #10 X 2” (51 mm) screw through top mounting hole in cabinet and screw into wall stud as shown. Do not overtighten screw. 4. Installez une vis #10 X 2” (51 mm) dans les colombages tel qu’illustré. Ne pas serrer trop les vis. 5.
PAGE 11
SURFACE MOUNTING / MONTAGE EN SURFACE / MONTAJE EN SUPERFICIE These instructions are for surface mounting your cabinet. Remove and store door with corner guards prior to installation. Determine overall cabinet dimensions on page 6. 1-4 Ces instructions sont pour le montage en surface de votre armoire. Retirez et rangez la porte avec les protège coins avant l’installation. Déterminez les dimensions globales de l’armoire en page 6. Estas instrucciones son para el montaje de su gabinete en superficie.
PAGE 12
SURFACE MOUNTING / MONTAGE EN SURFACE / MONTAJE EN SUPERFICIE 3. Center Z bar at cabinet location. Make sure Z bar is at least 1” (25mm) above fixtures. 4. Locate and drill three 7/32” (5,5mm,5.5mm) holes through the indent line on the mounting bar. Be sure the mounting bar is level. Make sure Z mounting bar is centered. 5a. Use three #10 X 2” (51 mm) screws provided to attach the Z bar mounting strip to the wall. 3 3. Centrez la barre en Z dans l’emplacement de l’armoire.
PAGE 13
SURFACE MOUNTING / MONTAGE EN SURFACE / MONTAJE EN SUPERFICIE 5b. If no furring strip or stud is available, use the supplied plastic anchors, making sure that each cabinet is supported by at least 3 anchors. Drill a 9/32” (7mm) hole for wall anchors. 5c. Tighten screw until it is tight against the Z bar. Keep turning screw at least 4 times as shown. 6a. Slide the four “Z” clips into the screw channel at the top of the cabinet; be sure that the “Z” clips lock into the grooves. 6b.
PAGE 14
SURFACE MOUNTING / MONTAGE EN SURFACE / MONTAJE EN SUPERFICIE 9. Attach Optional Side Kit (sold separately) to cabinet using supplied screws from inside cabinet box into Side Kit. Test the fit of the cabinet before completing installation. Cap the screws with the screw caps provided. For top mounted light fixtures, use the optional side kit sold separately. 6-screw cap le plug 22 for final assembly.
PAGE 15
GANGING CABINETS / AMALGAMER LES ARMOIRES / GABINETES ACOPLADOS HARDWARE BAG for assembling These are general instructions SAC DE QUINCAILLERIE cabinets together using ganging kit, ordered BOLSA DE ACCESORIOS separately. If assembling cabinets and lighting, refer to the instructions included with the lighting. Assemble cabinets on a level surface. Voici les instructions générales pour l’assemblage d’armoires ensemble à l’aide de l’ensemble d’amalgame commandé séparément.
PAGE 16
RECESS GANGING / AMALGAME ENCASTRÉ / ACOPLAMIENTO EMPOTRADO These are general instructions for recessing cabinets and/or with lighting. Refer to recess mounting instructions on page 7. Refer to lighting model instructions for specific details on how to assemble light. 1. When ganging cabinets and lighting, calculate rough opening width by subtracting 3/4” (19mm) from the total width and height of cabinets and lighting. See page 6 for model dimensions. 1b. Provide a separate switch for all lighting options.
PAGE 17
RECESS GANGING / AMALGAME ENCASTRÉ / ACOPLAMIENTO EMPOTRADO 3. Pull electric wire through the holes for all electric option cabinets and lighting. Be sure to provide enough wire to make proper and safe connections. 2-3 3. Tirez les câbles électriques par les trous pour toutes les options électriques des armoires. Assurez-vous de fournir suffisamment de fil pour faire des connections adéquates et sécuritaires. 3.
PAGE 18
RECESS GANGING / AMALGAME ENCASTRÉ / ACOPLAMIENTO EMPOTRADO 5. Make sure cabinet assembly is centered, level, and plumb, and then tighten the screws. 5. Assurez-vous que l’assemblage d’armoire est centré, à niveau et d’aplombs, puis serrez les vis. 3-3 5. Asegúrese que el ensamblado del gabinete esté centrado, nivelado y aplomado, y luego ajuste los tornillos. CAUTION: On installations of larger cabinet in combinations of 3 or more, the center door, when open, may cause the cabinet to bow from the wall.
PAGE 19
SURFACE GANGING / AMALGAME EN SURFACE / ACOPLAMIENTO EN SUPERFICIE These instructions are for surface mounting multiple cabinets and/or with lighting. Refer to page 11 for general surface mounting information. Refer to lighting instructions for specific details on how to assemble light. Determine overall dimensions of cabinets and lighting from page 6 for placement on wall. IMPORTANT: A complete 3-door unit is 120 - 150 pounds (54.4 - 68 kg) when empty. Use 1” X 3” (25.4 mm x 76.
PAGE 20
SURFACE GANGING / AMALGAME EN SURFACE / ACOPLAMIENTO EN SUPERFICIE 1a. Electrical Option Cabinets: Determine location of electrical rough-in for all electrical option cabinets. A punch-out hole is provided on the center line from 6 11/16” high from base of cabinet for electric option cabinets. See page 7. 1b. Optional light kit: Determine location of electrical rough-in for all optional lighting kits. Provide a separate switch for all lighting options.
PAGE 21
SURFACE GANGING / AMALGAME EN SURFACE / ACOPLAMIENTO EN SUPERFICIE 2. Pull electric wire through the holes for all lighting. Be sure to provide enough wire to make proper and safe connections. 3. Optional light kit: Wire each light base as defined in the specific lighting installation manual provided with the light fixture. Reassemble the light fixture. 4. IMPORTANT: When surface mounting with an optional top mounted light, use three large “Z” clips which are supplied with the light fixture.
PAGE 22
FINAL ASSEMBLY / ASSEMBLAGE FINAL / ENSAMBLADO FINAL 1a-b. Mount the doors following the instructions supplied with the hinge. The doors will swing 170°. If an optional light kit is installed, snap a hinge clip over the elbow of the hinges to stop door swing radius at 110° before installing lights. 2. The cabinet doors have a three-way adjustment feature. Height, level, and fit-toframe can all be adjusted using a #2 Phillips Head screwdriver. 3.
PAGE 23
USE AND MAINTENANCE / UTILISATION ET ENTRETIEN / USO Y MANTENIMIENTO The cabinet door and interior are constructed of mirrored glass and aluminum. Use only a damp cloth to clean. Ammonia or vinegarbased cleaners can damage mirrors. A 50/50 solution of water and isopropyl alcohol is recommended for cleaning the mirrors. A mild detergent may be used on the surfaces. When cleaning, spray the cloth, not the cabinet, mirror, or surround surfaces. Do not use abrasive cleansers on any part of the cabinet.
PAGE 24
WARRANTY / GARANTIE / GARANTÍA 1-1 Limited Warranty One Year Term Garantie limitée d’une durée d’un an Garantía Limitada Término de Un Año ROBERN warrants to the original purchaser that, it will, at its election repair, replace, or make appropriate adjustment to products made by this company shown to have significant defects in material or workmanship which are reported to ROBERN in writing within one (1) year from the date of delivery. ROBERN is not responsible for installation costs.