Installation & Assembly

ManualsBrandsRobern ManualsBathroom Remodel & Bathroom FixturesCurated Cartesian 31" Single Bathroom Vanity Set with Mirror

800.877.2376 www.robern.com

Installation instructions

Part no. 209-1276-rA rev. 06/06/17

Curated Cartesian H2 - 3 Drawer

CURATED CARTESIAN

™

VANITY

H4-3 DRAWER

This instruction manual contains information on how to install the 30" high Cartesian Vanity. This series comes in several sizes and

variations. Electrical option(s) may be provided with your vanity(s).

This vanity series needs special site preparation. Do not install vanities until all framing, plumbing and electrical option rough-ins have

been completed and wall surface has been nished. We recommend using the services of a professional installer. Observe all local

building codes.

Save these instructions for future use and reference. An improper installation voids the warranty. Installed vanities cannot be returned.

If you experience any problems with your vanities, contact your dealer or Robern directly.

CONTENT

Prep the wall - 3

Frame installation - 5

Attaching the side kits - 7

Installing any optional vanity accessories - 7

Sink assembly - 8

Insert the drawer - 10

Attaching glass drawer front - 11

GENERAL INFORMATION

Summary of content (13 pages)

PAGE 1
CURATED CARTESIAN™ VANITY H4-3 DRAWER CONTENT Prep the wall - 3 Frame installation - 5 Attaching the side kits - 7 Installing any optional vanity accessories - 7 Sink assembly - 8 Insert the drawer - 10 Attaching glass drawer front - 11 GENERAL INFORMATION This instruction manual contains information on how to install the 30" high Cartesian Vanity. This series comes in several sizes and variations. Electrical option(s) may be provided with your vanity(s). This vanity series needs special site preparation.
PAGE 2
TOOLS NEEDED Cloth PARTS [228-1015] Sink Box [216-1120] Sink Hardware Bag [203-1337] (4) Acorn Nut [210-1100] (2, 4, or 6) Bracket Stone Top [207-1065] Silicone Sealant Sink [1193643] (4) Bracket (not needed for this model) [203-1335] (4) #10-24 x 1.
PAGE 3
STEP 1 - PREP THE WALL 17" (432 mm) 32" (813 mm) 36-1/2" (927 mm) Side view showing blocking location in wall. 2x6 Drain 13-5/8" (346 mm) 17" (432 mm) 32" 34-1/2" (876 mm) Recommended height for undermount sink (813 mm) 5-5/8" (143 mm) 2x4 36-1/2" (927 mm) 2x4 Part no. 209-1276-rA rev. 06/06/17 Curated Cartesian H2 - 3 Drawer © 2017 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.
PAGE 4
STEP 1 - PREP THE WALL There are two types of electrical options available for vanities. The ﬁrst is a night light option ordered with the vanity. The second is an electrical accessory [VAELECTRIC]. Both of these options can be plugged into the same outlet. The outlet must be wired to a 120vac 20 amp GFCI circuit. We do not recommend using a GFCI outlet because resetting it under the vanity will be inconvenient. The night light has no switch.
PAGE 5
STEP 2 - FRAME INSTALLATION The drawer fronts are packed separately. Do not unpack them until the room is clear of hazards. 1. Mark the height for the vanity frame install on the finished wall and install two of the #10 x 2” (SS674) at the locations shown in Figure 1. Do not install tight to the wall, leave 1/8” behind the head. 2. Place the vanity frame on the screws using the top left and right keyholes. See Figure 2. The keyhole on the left allows for up and down adjustment.
PAGE 6
STEP 2 - FRAME INSTALLATION 3. Level the frame and tighten to the wall as shown here in Figure 3. The left keyhole is elongated to allow for up and down adjustment. 4. Install the four Structural Bolts (203-1256) into the four top frame holes. Figure 4. A T-30 Torx Bit is provided. 5. If the vanity doesn't sit level, or the wall is bowed, shim the frame as required. Shown in Figure 5. 6.
PAGE 7
STEP 3 - ATTACHING THE SIDE KITS Use the #10 CB-SS676 screws and washer CB-203-1198 provided to attach the side glass panels. [216-1077] Side kit Hardware Bag [203-1198] (9) Washer 9 [SS676] #10 x 1/2" Sheet metal screw STEP 4 - INSTALLING ANY OPTIONAL VANITY ACCESSORIES If you have the optional night light plug the unit in and test. See separate instructions for VAELECTRIC accessory. Part no. 209-1276-rA rev. 06/06/17 Curated Cartesian H2 - 3 Drawer © 2017 Robern, Inc. 701 N. Wilson Ave.
PAGE 8
STEP 5 - SINK ASSEMBLY 1. Thread the screws [203-1335] into the brackets [210-1100] and thread the acorn nuts [203-1337] onto the screws. Place the assembled brackets into the vanity opening(s). Brackets should be snug and flush to the top of the vanity. 2. Place the sink(s) into the opening(s) and position the sink(s) at the front of the vanity. Test fit the stone top to be sure the sink(s) is properly located. 3. Apply a 1/4" (6mm) bead of silicone sealant on both vanity and sink flange(s). 4.
PAGE 9
STEP 5 - SINK ASSEMBLY 5. Tighten the screws under the bracket so that the acorn nuts raises the sink and secures it to the stone top. Do not overtighten. 6. Verify that the stone top is level and wipe away excess silicone sealant. Allow the sealant to set according to the sealant manufacturer's instructions. 7. Install the faucet(s) to the stone top and drain(s) to the sink(s). Refer to the faucet and drain manufacturer's instructions. 8. Complete the faucet connections. Run water and check for leaks.
PAGE 10
STEP 6 - INSERT THE DRAWER If you are installing VAELECTRIC, see separate instructions before proceeding further. 1. Fully extend the bottom set of slide rails out from the frame. 2. Place the drawer into the slide rails. 3. To secure the drawer, close the drawer until a series of clicks are heard. 4. Repeat steps 1 thru 3 for middle drawer. 1 2 3 Part no. 209-1276-rA rev. 06/06/17 Curated Cartesian H2 - 3 Drawer © 2017 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A. 800.877.2376 www.robern.
PAGE 11
STEP 7 - ATTACHING GLASS DRAWER FRONT 1. Install 2 #8-32 x 1/2” screws (203-1219) WITHOUT washers on the bottom of each bracket in the drawer front. Do not tread all the way through so that the screw can be hung on the keyhole in the next step, See Figure 1. 2. Hang the drawer front on the two keyholes on each side of the drawer box. See Figure 2. 3. Install the remaining screws WITH washers into the two remaining threads in the drawer front bracket as shown in Figure 3.
PAGE 12
STEP 7 - ATTACHING GLASS DRAWER FRONT 5. Extend the middle drawer. 6. Thread the screw and washer through the holes inside the drawer to the glass front. 7. Install the screw caps as shown in figure 7. 8. Tilt the top tipout drawer down. 9. Thread the screw and washer through the holes inside the drawer to the glass front. 10. Install the screw caps as shown in figure 10. 5 6 7 8 9 10 Part no. 209-1276-rA rev. 06/06/17 Curated Cartesian H2 - 3 Drawer © 2017 Robern, Inc. 701 N. Wilson Ave.
PAGE 13
USE AND MAINTENANCE The vanity sides, drawer front and interior are constructed of glass and aluminum. Use only a damp cloth to clean. Ammonia or vinegarbased cleaners can damage mirrors. A 50/50 solution of water and isopropyl alcohol is recommended for cleaning the vanity. A mild detergent may be used on the surfaces. When cleaning, spray the cloth, not the vanity, mirror, or surround surfaces. Do not use abrasive cleansers on any part of the vanity.