Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from backplate (B) by removing screws (C). Set screws (C) aside.
2. Determine desired location for light xture on wall. Hold mounting plate (A) in a level position against the wall. Using a pencil, mark the
location of the mounting holes in mounting plate (A) onto the wall.
3. Drill small holes at marked locations on the wall. Holes should be sized so they accommodate wall anchors (J), provided. Insert wall anchors
into drilled holes.
4. Afx mounting plate (A) to the wall by threading mounting screws (D) through holes in mounting plate (A) and into wall anchors.
5. Slide backplate (B) over mounting plate (A). Thread screws (C) back into holes at the top and sides of backplate (B) to secure xture to the
mounting surface.
6. Thread cord cover (G) into nipple (F) at the bottom of the backplate. Thread cord cover (H) onto cord cover (G).
7. Insert one 60W Max Type A, medium base bulb into the socket.
8. Attach shade cover (M) to shade (L) using screws (N).
9. Insert three prong plug (I) into wall outlet.
10. Control power to xture by rotating the switch on back plate (B).
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER. IT IS RECOMMENDED
THAT A LICENSED ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from backplate (B) by removing screws (C). Set screws (C) aside.
3. Cut three prong plug (I) from the end of the electrical cord.
4. Remove cord covers (G) and (H) from the electrical cord. From the back side of backplate (B), pull the electrical cord up through
nipple (F).
5. Cut the cord to the desired length for making an electrical connection. At least six inches of wire will be needed to make proper
electrical connection.
6. Carefully unscrew nipple (F) from backplate (B). Thread plug (E) into the hole vacated by the electrical cord and nipple (F).
7. Carefully pull the wiring from wall outlet box. Thread the wires through the center hole in mounting plate (A).
8. Afx mounting plate (A) to wall outlet box with mounting screws (D) provided.
9. Lift xture to mounting plate and make proper electrical connections described in steps 10 - 12. A LICENSED ELECTRICIAN IS
RECOMMENDED.
10. Connect ground (green or silver in color) wire from xture to ground wire in the outlet box. Fasten wires together with wire nut (K)
and tightly wrap the connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut
(K) and tightly wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with
wire nut (K) and tightly wrap connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide backplate (B) over mounting plate (A).
14. Thread screws (C) into vacant holes at the top and sides of backplate (B) to secure the xture to the mounting surface.
15. Insert one 60W Max Type A, medium base bulb into the socket.
16. Attach shade cover (M) to shade (L) using screws (N).
17. Reconnect main electrical supply at fuse box/ circuit breaker and test the xture.
18. Control power to xture by rotating the switch on back plate (B).
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners. *
S1581
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety instructions are read before beginning installation of xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn off power at switch before replacing bulbs, making sure xture has had sufcient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
ASSEMBLY INSTRUCTIONS FOR YOUR
APOLLO SCONCE