Installation Guide

ASSEMBLY INSTRUCTIONS FOR YOUR
LARGE ANDROMEDA PENDANT
166
ASSEMBLY INSTRUCTIONS:
* These instructions are provided for your safety. It is very important that they are read
completely before beginning the installation of your xture.
* WE STRONGLY RECOMMEND INSTALLATION BY A LICENSED
ELECTRICIAN.
* Turn o power at switch before replacing bulbs
* If any special control devices are used with this xture, follow the instructions carefully
to assure full compliance with N.E.C. requirements. If there are any questions, contact a
qualied electrical contractor.
* This xture is UL rated for dry locations.
IMPORTANT SAFETY INSTRUCTIONS:
(H)
(I)
(I)
(I)
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(N)
(J )
(M)
(K)
(L)
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX/ CIRCUIT
BREAKER.
2. Remove all parts from carton. Do not throw away any parts.
3. Remove quick link (G) from hang straight (F). Keep quick link (G) attached to loop (H).
4. Remove cross bar (A) (with threaded tube (C) and hang straight (F) attached) from
canopy (D). Do this by unthreading collar (E) from hang straight (F). Carefully slide
collar (E) down extensions (I) until it rests on threaded tube (J). Slide canopy (D) over
hang straight (F) and down extensions (I) until it rests on collar (E).
5. Ax cross bar (A) (with threaded tube (C) and hang straight (F) attached) to ceiling
outlet box using screws (B) provided.
6. Measure desired drop for xture to hang and add/remove extension tubes (I) to reach
desired position. Guide wiring through extension tubes before threading tubes together.
**TO ADD/REMOVE EXTENSIONS: (Un)Thread the threaded tube of one
extension out of/ into the threaded opening of the next extension. Make sure wiring
is pulled tight when threading extensions together to prevent damage to the wire.**
7. Thread bottom extension tube (I) onto threaded tube (J).
8. Lift xture to ceiling and secure quick link (G) to hang straight (F). Carefully guide
wire through hang straight (F) and threaded tube (C) into ceiling outlet box.
9. Make proper electrical connections noted in steps 10-12. A
LICENSED ELECTRICIAN IS RECOMMENDED.
10. Attach ground wire from xture (green or silver in color) to
ground wire from outlet box. Fasten wires together with wire
nut (N) and tightly wrap connection with electrical tape.
11. Attach hot wire from xture (black in color or smooth side of
wire) to hot wire from outlet box. Fasten wires together with
wire nut (N) and tightly wrap connection with electrical tape.
12. Attach neutral wire from xture (white in color or ribbed side
of wire) to neutral wire from outlet box. Fasten wires together
with wire nut (N) and tightly wrap connection with electrical
tape.
13. Carefully push wire connections back into ceiling outlet box.
14. Gently push wires back into ceiling outlet box.
15. Slide canopy (D) up extensions (I) and hold ush against
ceiling. To secure position of canopy (D), slide collar (E) up
extensions (I) and thread it onto the hang straight (F). Turn
until hand tight.
16. Install eight (8) 40W MAX. Type G, candelabra base bulbs into
the sockets (L).
17. Thread acrylic rods (M) into housing (K) to complete assembly.
Note: Grasp acrylic rods at base, near threads to avoid damage
to acrylic and cap. Do not force rods into housing. If you
experience diculty threading a rod into the housing at chosen
spot, don’t try to force the parts to thread together. Instead, try
threading the rod into a dierent opening in the housing.
***To clean, use soft cloth only. Do not use any chemical or abrasive cleaners.***