Installation Guide

CORD COVER ASSEMBLY INSTRUCTIONS:
1. Remove mounting plate (A) from back plate (B) by removing screws (C).
2. Determine desired location for light fi xture on wall. Hold mounting plate (A) in a
level position against the wall. Using a pencil, mark the location of the mounting
holes in mounting plate (A) onto the wall.
3. Drill holes at marked locations on the wall. Holes should be sized so wall anchors
(I) fi t snug inside the openings. Insert wall anchors into the drilled holes.
4. Affi x mounting plate (A) to the wall by threading mounting screws (N) through
holes in mounting plate (A) and into wall anchors (I).
5. Slide back plate (B) over mounting plate (A). Thread screws (C) back into holes
at the top and sides of back plate (B) to secure fi xture to the mounting surface.
6. Thread cord cover (F) into the bottom of the back plate (B). Thread cord cover (G)
onto cord cover (F).
7. Follow steps 15 and 16 from Direct Wire Assembly Instructions, below.
8. Insert three prong plug (H) into wall outlet.
9. Control power to the fi xture by rotating the switch on the back plate (B).
DIRECT WIRE ASSEMBLY INSTRUCTIONS:
1. SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER. IT IS RECOMMENDED THAT A LICENSED
ELECTRICIAN INSTALL THIS FIXTURE.
2. Remove mounting plate (A) from back plate (B) by removing screws (C).
3. Cut three prong plug (H) from the end of the electrical cord.
4. Remove cord covers (F) and (G) from the electrical cord. From the back side of
back plate (B), pull electrical cord up through hole in the bottom of back plate.
5. Cut the cord to the desired length for making an electrical connection. At least
six inches of wire will be needed to make proper electrical connection.
6. Thread plug (E) into the hole vacated by the electrical cord.
7. Carefully pull the wiring from wall outlet box. Thread the wires through the
center hole in mounting plate (A).
8. Affi x mounting plate (A) to wall outlet box with mounting screws (D) provided.
9. Lift fi xture to mounting plate and make proper electrical connections described
in steps 10 - 12. A LICENSED ELECTRICIAN IS RECOMMENDED.
10. Connect ground (green or silver in color) wire from fi xture to ground wire in
the outlet box. Fasten wires together with wire nut (J) and tightly wrap the
connection with electrical tape.
11. Attach hot wire from fi xture (black in color or smooth side of wire) to hot wire
from outlet box. Fasten wires together with wire nut (J) and tightly wrap
connection with electrical tape.
12. Attach neutral wire from fi xture (white in color or ribbed side of wire) to neutral
wire from outlet box. Fasten wires together with wire nut (J) and tightly wrap
connection with electrical tape.
13. Carefully push wire connections back into wall outlet box. Slide back plate (B)
over mounting plate (A).
14. Thread screws (C) into vacant holes at the top and sides of back plate (B) to
secure the fi xture to the mounting surface.
15. Remove fl ange (K) from socket (M). Place shade (L) onto socket (M). Thread
fl ange (K) back onto socket (M) to secure shade to fi xture.
16. Insert one 60W MAX. Type B candelabra base bulb into socket (M).
17. Reconnect main electrical supply at the fuse box/circuit breaker and test fi xture.
18. Control power to the fi xture by rotating the switch on the back plate (B).
* To clean, use a soft dry cloth. Do not use any chemical or abrasive cleaners. *
3397
IMPORTANT SAFETY INSTRUCTIONS:
* These instructions are provided for your safety. It’s important that all safety
instructions are read before beginning installation of fi xture.
* We STRONGLY recommend installation by a licensed electrician.
* Turn off power at switch before replacing bulbs, making sure fi xture has had
suffi cient time to cool down.
* Do not connect the electricity until lamp is fully assembled.
ASSEMBLY INSTRUCTIONS FOR YOUR
TRIGGER WALL SCONCE
(J )
(I)
(N)
(D)
(A)
(B)
(E)
(C)
(M)
(L)
(K)
(F)
(G)
(H)