Installation Guide

1315
ASSEMBLY INSTRUCTIONS FOR YOUR
RODERICK HALOGEN
DOUBLE SCONCE
(A)
(C)
(C)
(B)
(D)
(J)
(E)
(I)
"J BOX"
(F)
(G)
BULB
(H)
(A)
(H)
BULB
FIG. A
VERTICAL
MOUNT
(K)
SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX /
CIRCUIT BREAKER.
1. Remove all parts carefully from the box.
2. Remove glass shades (A) by unscrewing from threaded socket cover (B).
3. Remove backplate screws (C) from backplate (D).
4. Carefully position adapter plate (G) behind mounting plate (F) and guide
wires from xture through hole (J) located at bottom of mounting plate (F)
and hole (K) located at the bottom of adapter plate (G).
5. Make proper electrical connection with wiring exiting bottom hole
of adapter plate (G).
6. Connect ground wire (green) from the xture to the ground wire in outlet box.
Connect the black wire of the xture (or smooth side of the wire) to the black
wire in the outlet box using wire nuts (H). Connect the white wire of the
xture (or rough side of the wire) to the white wire in the outlet box using
wire nuts (H).
7. Afx mounting plate (F) and adapter plate (G) to “J BOX” by inserting
mounting plate screw (I) into slotted hole on bottom of mounting plate (F) and
slotted hole on bottom of adapter plate (G). Thread screw (I) into bottom hole
of “J BOX.”
8. After mounting plate and adapter plate are moved into desired position, insert
mounting plate screw (E) into slotted hole in top of mounting plate (F) and
slotted hole in top of adapter plate (G) and thread screw (E) into drywall
above “J BOX”. Make sure to use threaded plastic sleeve (included) over
mounting plate screw (E) when attaching xture to drywall.
9. Align holes in top and bottom of backplate (D) with screw holes in top and
bottom of mounting plate (F).
10. Place backplate (D) over mounting plate (F). Thread backplate screws (C)
into backplate (D) to secure xture to mounting plate (F).
11. Install two 30W max bi-pin 12V G4 & GY6.35 halogen bulbs into sockets
12. Align threaded section of glass shades (A) with threaded openings of socket
cover (B). Thread glass shades (A) onto threaded socket cover (B) until tight.
FIG. B
HORIZONTAL
MOUNT
(L)
(M)
(I)
(E)
"J BOX"
(F)
(G)
VERTICAL MOUNTING
HORIZONTAL MOUNTING
1. Follow steps 1 -3 listed above.
2. Carefully position adapter plate (G) behind mounting plate (F) and guide
wires from xture through hole (M) located in the middle of mounting plate
(F) and hole (K) located in the middle of adapter plate (G).
3. Follow steps 5 - 6 listed above.
4. Position mounting plate (F) and adapter plate (G) horizontally over “J
BOX”. Afx mounting plate (F) and adapter plate (G) to drywall on right and
left side of “J BOX” by inserting mounting plate screws (E) and (I) into
slotted holes on right and left side of mounting plate (F) and adapter plate (G).
Make sure to use threaded plastic sleeve (included) over mounting plate
screws (E), and (I) when attaching xture to drywall.
5. Follow steps 9 - 12 listed above.
WARNING: If any special control devices are used with this xture, follow the
instructions carefully to assure compliance with N.E.C. requirements. If there are
any questions, contact a qualied electrical contractor.
DIMMER WARNING:
When using a dimmer device with this xture, a specic Electronic Low Voltage
(ELV) dimmer must be used to avoid potential damage to the transformer.
WE STRONGLY RECOMMEND INSTALLATION OF FIXTURE BE
PROFORMED BY A LICENSED ELECTRICIAN.