Sound for Generations ROBERTS CR9923 2 Band Single Alarm Clock Radio FM PM MW 60 92 0 540 kHz 88 MH z TUNING CR 9923 2 Band Clock Radio Please read this manual before use
Controls (top) 1 2 3 ALARM/OFF SLEEP Minute 4 5 1. Alarm set/off button. 2. Sleep button. 3. Minute button. 4. Hour button. 5. Time set button. 6. Snooze.
Controls (front) 7 6 8 6. Alarm indicator. 7. PM indicator. 8. Tuning control.
Controls (left and right side) On Off Radio Buzz 9 9. Function switch. 10. Dimmer switch. 11. Waveband switch. 12. Volume control. DIMMER High Low 10 11 MW FM 13.
Switching on 1. Place your clock radio on a flat surface. Plug the power cord into the wall socket and switch on. The clock display will flash 12.00. ON FM PM MW 60 92 0 540 kHz 88 MHz TUNING CR 9923 2 Band Clock Radio TIME Setting the time 1. Press and hold down the TIME button. 2. Whilst holding down the TIME button press the Hour or Minute buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with an PM indicator.
Listening to the Radio On Off Radio Buzz 1. Switch on the radio by sliding the Function switch to the 'On' position. 2. Select the required waveband using the Waveband selector switch. MW FM 3. Tune in to the desired station by rotating the Tuning control. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. For MW reception there is a built in ferrite aerial.
Setting alarm time ALARM/OFF Minute 1. Press and hold down the ALARM/OFF button. Hour 2. Whilst holding down the ALARM/OFF button press the Hour or Minute buttons to set the time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. PM Checking the alarm time 1. To check alarm time, press and hold down the ALARM/OFF button the display will show the alarm time.
Setting the alarm to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. The Alarm indicator will light. The alarm will sound every day at the preset time for 1 hour 59 minutes. To switch off the alarm until the next day press the ALARM/ OFF button. To turn off the alarm permanently set the Function switch to the 'Off' position. On Off Radio Buzz PM Setting the alarm to wake to radio 1. Set the alarm time as previously described.
Snooze control 1. The radio or buzzer alarm can be silenced for 9 minutes by pressing the SNOOZE button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to turn off after a preset time has elapsed. SNOOZE SLEEP PM 1. Press and hold down the SLEEP button. 2. Whilst holding down the SLEEP button set the sleep time using the Hour and Minute buttons (maximum 1 hour and 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed. 3.
Dimmer Switch DIMMER The DIMMER switch located on the left side of your clock radio will allow you to adjust the intensity of the clock display to suit room brightness. High Low Circuit Features Specifications Loudspeaker Power Requirements Mains : Back-up Battery AC 230 volts, 50Hz only : IEC size 6LR61 (6F22, PP3) Frequency Coverage FM MW 87.
General E (Earth) Do not allow this unit to be exposed to water or steam. It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW band. Brown (Live) 3 amp L Blue (Neutral) Mains supply The CR9923 will operate from a supply of AC 230volts, 50Hz only. For your convenience this product is supplied with a plug which is fitted with a fuse of the appropriate rating.
Guarantee This clock radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Product with removed or defaced serial numbers.