Specification

48 hours to allow adhesive to cure
properly. Premature traffic can
cause installation failure.
Clean Up: Fresh adhesive – warm
soapy water. Dried adhesive – use
mineral spirits sparingly with a clean,
white cotton cloth. DO NOT POUR
CLEANER DIRECTLY ONTO FLOORING.
Refer to material safety data sheet,
www.robertsconsolidated.com and
industry standards prior to installation
for additional information. For installation
questions that are not covered in this document please contact our
Technical Services Department at [phone].
Limited Warranty: Buyer assumes all risk of use, handling and storage
of product not in strict accordance with the label, printed literature and
industry standards. This limited warranty excludes all other express
or implied warranties including the warranties of merchantability or
fitness for a particular use or purpose. Any implied warranties arising
by operation of law are limited to one year. Roberts will not be liable for
any incidental or consequential damages. Some states do not allow
these limitations or exclusions, therefore they may not apply. This
warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
Available Sizes:
WARNING: EXISTING FLOORING AND ADHESIVES MAY
CONTAIN ASBESTOS. Unless you have confirmation that the
existing flooring system is not asbestos containing, do not
sand, dry sweep, dry scrape, abrade, drill, saw, bead blast,
mechanically chip or pulverize existing flooring or adhesive
without taking all appropriate precautions. Refer to local, state
and federal guidelines for treatment and removal of these
products. You may also refer to the Resilient Floor Covering
Institute’s “Recommended Work Practices for Removal of
Resilient Floor Coverings.”
EXISTING PAINT MAY CONTAIN LEAD. Unless you have
confirmation that the existing paint is not lead containing, do
not sand, dry sweep, dry scrape, abrade, drill, saw, bead blast,
mechanically chip or pulverize existing paint without taking
all appropriate precautions. Refer to local, state and federal
guidelines for treatment and removal of lead containing paint.
You may also refer to www.epa.gov/lead
General (continued):
Flooring must be installed when the indoor temperature is between
65–95°F (18–35°C) with a maximum RH of 65%, 48 hours before, during
and 72 hours afterward. Large temperature or humidity increases or
decreases can affect the flooring and performance of the installation.
Physical Characteristics (70°F, RH 50%):
Open Time: Up to 20 minutes
Working Time: Up to 40 minutes
Shelf Life: One year in unopened container
Product Type: SBR latex
Moisture Vapor Emissions: 3 lbs. or less (ASTM F1869) /
75% or less (ASTM F2170)
Protect from freezing
Application and Installation: Spread adhesive uniformly. Allow up to
twenty minutes of open time before you place your flooring into the
adhesive. Adhesive ridges should be of sufficient height to achieve full
coverage of the substrate and the deepest recesses in the back of the
flooring material.
Within the 40 minute working time, place flooring into the adhesive
while the adhesive is still fresh and transfers readily to the flooring
backing. The amount of open time and time in which you have time to
place the flooring will vary with temperature and humidity. The higher
the temperature and the
lower the humidity the faster
the adhesive will set.
Lift a corner periodically to
see if the adhesive is
transferring 100% to the
back of the flooring. If the
adhesive is not transferring
to the backing of the
underlayment remove
adhesive and reapply.
After Installation – Restrict
foot traffic and moving of
heavy objects for 24 to
Roberts Consolidated Industries, Inc. • Boca Raton, FL 33487 • [phone] • www.robertsconsolidated.com 2
D179_5541
5 Gallon (18.9 L) 3095-5 075378309550
4 Gallon (15.14 L) 3095-4 075378309543
1 Gallon (3.78 L) 3095-1 075378309512
SIZE PRODUCT # UPC