Specification

afterward. Large temperature or humidity increases or decreases
can affect the wall base and performance of the installation.
Ensure adequate ventilation during wall base installation.
Physical Characteristics (70°F, RH 50%):
Open Time: Up to 10 minutes
Working Time: Up to 30 minutes
Shelf Life: One year in unopened container
Protect from freezing
Application and Installation: Trim any vinyl wall coverings to 1/4 in.
below the top of the wall base with Roberts 10-215 or 10-920-6 knife.
Spread adhesive uniformly to the wall or to the back of the wall base.
Cartridges: 30 oz. – Unscrew cap, cut top seal, replace cap, load
Roberts 10-981-25 Snozzle and place in Roberts 10-980 30 oz. cartridge
gun. 11 oz. – Cut tip, load Roberts Snozzle and place into 11 oz.
cartridge gun. Squeeze gun gently, with even pressure, to apply.
Press the wall base firmly in place while the adhesive is still wet
(typically within 10 minutes). Note: The amount of time in which you
have to place the wall base will vary with temperature and humidity.
Roberts
®
7200 is a superior performing wall base adhesive with
quick grab and rapid set-up for the fast installation of wall base.
Features:
• Excellent holding power • Fast set-up
• Strong initial grab for holding • Non-staining
heavy rubber wall base
Enviro Friendly:
• Solvent Free • Zero VOCs (calculated)
Roberts 7200 is a VOC Compliant adhesive and meets the strict
requirements of the South Coast Air Quality Management District and
may contribute one LEED point as a “Low Emitting Adhesive.”
Roberts 7200 is protected by GoldGuard
®
, an antimicrobial protection
system that inhibits the growth of mold, mildew and odor causing
bacteria in both wet and dry adhesive.
Uses: For adhering vinyl, rubber and carpet wall base.
Installation Surfaces: Porous wall surfaces such as gypsum drywall,
plaster, brick, concrete block and wood. Roberts 7200 is not
recommended over non-porous or painted surfaces.
Surface Preparation: Surface must be structurally sound, dry, smooth,
flat and free of excess moisture/alkali and all substances (oil, grease,
paint, wall paper, sealers, dust, etc.) that might interfere with the
performance of the wall base or its installation. Do
not install over non-porous surfaces.
All cracks, holes, high spots and irregularities must
be adequately repaired to ensure a smooth, finished
appearance. Patching compounds must be suitable
for the use application, polymer-fortified and applied
according to the manufacturer’s instructions.
General: Concrete and plaster must be properly
seasoned and dry prior to installation. Ensure wall
surface, wall base and adhesive are fully acclimated
prior to installation at the same temperature and
humidity level expected during normal use (between
65–95°F with a relative humidity (RH) of no greater
than 65%). Refer to wall base manufacturer’s specific
recommendations and industry standards.
Materials and area temperature must be between
65–95°F with a maximum RH of 65% for 48 hours
before and during installation as well as for 72 hours
e
n
v
i
r
o
f
r
i
e
n
d
l
y
™
Wall Base Adhesive
Roberts Consolidated Industries, Inc. • Boca Raton, FL 33487 • [phone] • www.robertsconsolidated.com
The trowel notches referenced are those typically recommended for wall base. They are
normally the minimum size recommended. Consult wall base manufacturer for their specific
trowel recommendations. Surface conditions (roughness and porosity of wall surface) and
type of wall base will ultimately determine the required trowel notch size and coverage. Ensure
100% transfer of adhesive to the wall base and the wall surface.
FLOORING TYPE TROWEL SIZE ROBERTS ITEM # COVERAGE
1
Wall Base (4 in.)
20–24 lin. ft./11 ounces
55–65 lin. ft./30 ounces
10033
3/16 in. x 5/32 in
1/8 in. x 1/8 in.
Wall Base (4 in.)
16–20 lin. ft./11 ounces
45–55 lin. ft./30 ounces
n/a
Snozzle
13–22 lin. ft./11 ounces
50–60 lin. ft./30 ounces
10-981-25
Wall Base (4 in.)
SUPERIOR
7200
ANTIMICROBIAL PROTECTION
®