MSDS

MATERIAL SAFETY DATA
PRODUCT NAME: Roberts 8015 Solvent Free Universal Carpet Seam Adhesive HMIS CODES: H F R
1 0 0
SECTION I - MANUFACTURER IDENTIFICATION
GENERIC ID:
Acrylic copolymer blend.
SUPPLIER'S NAME: ROBERTS CONSOLIDATED INDUSTRIES
ADDRESS:
2070 Steeles Ave. Bramalea, Ontario L6T 1A7 Canada
EMERGENCY PHONE: [phone] (Chemtrec) INFORMATION PHONE:
[phone]
DATE REVISED: 2/24/2010
PREPARED BY: M. King
SECTION II - HAZARDOUS COMPONENTS:
NO REPORTABLE INGREDIENTS
SECTION III - PHYSICAL DATA
Boiling Point: 212 F. Vapor Pressure: Same as water Vapor Density (Air=1.0 Same as water . Specific Gravity: 1.04.
Percent Volatiles: 46 - 49% by weight.
Evaporation Rate (nBuAc=1) Same as water.
VOC (Calculated):
So low as to be indeterminate. APPEARANCE & ODOR: White liquid, mild odor.
SECTION IV – FIRE AND EXPLOSION DATA
Flash Point: NA. Auto-Ignition Temperature: NA.
Flammable Limits in air, Volume %: Lower: = NA Upper: = NA.
Extinguishing Media: Water Spray, CO², Foam, Dry Chemical. HAZARDOUS DECOMPOSITION PRODUCTS: N/A SPECIAL
FIRE FIGHTING PROCEDURES: Self-contained breathing apparatus should be worn.
UNUSUAL FIRE AND EXPLOSION HAZARD: None.
SECTION V - HEALTH HAZARD DATA
HEALTH EFFECTS OR RISKS FROM EXPOSURE:
Acute: May cause mild skin irritation, irritation of respiratory tract. Chronic: None known.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None Known.
SYMPTOMS OF OVEREXPOSURE: Eyes: May cause irritation. Skin: May cause mild irritation. Inhalation: May cause irritation to
upper respiratory tract. Ingestion: Not a likely route of entry under proper handling conditions. Symptoms may be the same as
inhalation.
FIRST AID: Eye contact: Flush with water for at least 15 minutes. If irritation persists, seek medical attention. Skin contact:
Remove contaminated clothing and wash affected areas with soap and water. If irritation persists, see a physician. Inhalation:
Remove to fresh air, administer oxygen and if necessary, seek medical attention. Ingestion: Not a likely route of entry under proper
handling conditions. Seek medical attention if necessary.
SUSPECTED CANCER AGENT: No.
SECTION VI - REACTIVITY DATA
Hazardous Polymerization: Does not occur. Stability: Stable. Incompatibility: Oxidizing materials.
Hazardous Decomposition Products (including combustion products): Oxides of carbon (CO, CO2), water and organic
compounds of unknown structure.
Corrosive to Metal: No. Oxidizer: No
Conditions to avoid: : Excessive Heat, Freezing.
SECTION VII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Absorb or scrape up. Wash area with water to remove residue. Spilled material may cause slippery conditions. Promptly
report significant spills to appropriate authorities. Consult local regulations.
Note: Dispose of all wastes in accordance with Federal, State and Local regulations.
SECTION VIII - PROTECTIVE EQUIPMENT
VENTILATION:
General dilution ventilation. Do not use closed air circulating system.
RESPIRATOR PROTECTION:
Not required under normal conditions of use.
PROTECTIVE GLOVES:
Polyethylene, PVC, natural rubber. EYE PROTECTION: Wear chemical goggles or face shield.
OTHER PROTECTIVE EQUIPMENT: If clothing becomes contaminated, remove and clean before re-wearing.
WORK PRACTICES, HYGIENIC PRACTICES: Follow all label instructions.
PROTECTIVE MEASURES DURING MAINTENANCE OF CONTAMINATED EQUIPMENT: Use goggles and gloves when cleaning
adhesive from equipment. Maintain proper ventilation.