3 Band Single Alarm Night Light Clock Radio Sound for Generations ROBERTS CR9932 Please read this manual before use
Controls (Top) 3 4 5 2 6 1 12 (Left side) 1 11 10 9 8 7 (Right side) 1. Dimmer switch 5. Waveband selector 2. Function switch 6. Tuning control 9. Alarm/Off button 3. Headphone socket 7. Snooze/night light button 11. Minute button 4. Volume control 8. Sleep button 12. Hour button 10.
Controls (Front) 14 13 16 15 13. PM indicator 14. LED dial pointer 15. Battery compartment (underside) 16.
Switching on and setting the time Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the power cord into the wall socket and switch on. 2. The clock display will flash 12:00. 3. Press and hold down the Time Set button. 4. Whilst holding down the Time Set button press the Hour, or Minute buttons to set the time. Release the buttons when the correct time is reached. The clock uses a 12 hour display with a PM indicator.
Listening to the Radio 1. Turn on the radio by sliding the Function switch to the 'On ' position. The LED dial pointer will light up indicating that the radio is switched on. 2. Select the required waveband using the Waveband selector switch. 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the LED dial pointer. The Wire aerial located on the rear of your clock radio is for FM reception.
Alarm The alarm can be set to wake you by either the buzzer or the radio. Setting alarm time 1. Press and hold down the Alarm/Off button. 2. Whilst holding down the Alarm/Off button press the Hour, or Minute buttons to set the time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. Checking the alarm time 1.
Setting the alarm to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the ' Buzz' position. The Alarm indicator will light. The alarm will sound every day at the preset time for 59 minutes. To turn off the alarm until the next day press the Alarm/Off button. To turn off the alarms permanently set the Function selector to the 'Off' position. Setting the alarms to wake to radio 1. Set the alarm time as previously described.
Snooze control The radio or buzzer alarm can be silenced for 7 minutes by pressing the Snooze Light button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to turn off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed. To cancel the sleep function before the preset time has expired, press the Alarm/Off button.
Headphones (on rear) A Headphone Socket (3.5mm) is provided for use with either headphones or an earpiece . Inserting a plug automatically mutes the internal loudspeaker. Night light Press the Snooze button once to turn on the night light. Press again to turn it off. The night-light will provide a warm glow adequate to allow movement around the room safely. It is not intended as a reading light.
General Fuse Do not allow this unit to be exposed to water or steam. It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW or LW bands. Mains supply Back-up Battery (not necessary for the unit to function) The CR9932 will operate from a supply of AC 230volts, 50Hz only. For your convenience this product is supplied with a plug which is fitted with a fuse of the appropriate rating.
Specifications Circuit Features Power Requirements Mains Back-up Battery AC 230 volts, 50Hz only IEC size 6LR61 (6F22,PP3) Loudspeaker Frequency Coverage FM MW LW 87.5 - 108MHz 525 - 1610kHz 147 - 284kHz 75mm diameter 8 ohms Output Power 0.3W RMS Aerial System FM Wire Aerial MW Built-in Ferrite aerial LW Built-in Ferrite aerial The Company reserves the right to amend the specification without notice.
Guarantee This radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Product with removed or defaced serial numbers.
