Sound for Generations ROBERTS CR9933 Dual Alarm Clock Radio with Nightlight Please read this manual before use
Contents Contents .................................................................................................................................................................................. 1 Controls ................................................................................................................................................................................ 2-4 Switching on and setting the time .........................................................................................
Controls 3 (Front) 4 (Top) 5 6 7 8 9 Night Light 2 On Off 1 10 Time 11 15 Snooze Sleep Alarm Set 12 14 13 1. Alarm 2 indicator 6. Time reverse button 11. Time set button 2. Alarm 1 indicator 7. Time forward button 12. Alarm set button 3. Dial pointer 8. Night light button 13. Snooze button 4. Time display 9. Time fast forward button 14. Sleep button 5. On button 10. Off button 15.
Controls (Left side) 19 (Right side) Tuning 16 18 17 21 20 3 16. Headphone socket 19. Volume control 17. Loud Speaker 20. Battery back-up compartment (underside) 18. Tuning control 21.
Controls (Back) 23 24 22 22. Waveband selector switch 23. Alarm 1 selector switch 24.
Switching on and setting the time Before using your clock radio you must first set the correct time. CR 9933 Night Light Dual Alarm 1. Place the unit on a flat surface. Plug the mains lead into a wall socket and switch on. 1 2 FM 88 90 92 94 96 100 102 105 108 MHz ON MW 540 600 700 800 1000 1200 1600 kHz PISAone 2. The clock display will flash 00.00. 3. Press and hold down the Time Set button. 4.
Listening to the radio 1. Switch on the radio by pressing the On button. 2. Select the required waveband using the Waveband selector switch. On 1 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated by the Dial pointer. 2 The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. FM MW For MW reception there is a built in ferrite aerial.
Setting alarm times The alarms can be set to wake you by either the buzzer or the radio. Your alarm clock radio has 2 separate alarms which can be set to activate at different times. Setting alarm 1 1 1 1. Slide the Alarm 1 selector switch to the preferred buzzer or radio position. Ensure that the Alarm 2 selector switch is Off. 2. Press and hold down the Alarm set button. 3.
Setting alarm 2 1. Slide the Alarm 2 function switch to the preferred buzzer or radio position. Ensure that the Alarm 1 selector switch is on Off while setting Alarm 2 but remember to switch Alarm 1 back to buzzer/radio after setting alarm 2. 1 1 2. Press and hold down the Alarm set button. 3. Whilst holding down the Alarm Set button press the Fast forward, Slow forward, Slow reverse or Fast reverse buttons to set the required alarm time. Release the buttons when the correct alarm time is reached.
Checking the alarm times 1. To check the time set on alarm 1, set the Alarm 1 selector switch to the buzzer or radio position. Ensure that the Alarm 2 selector switch is off while checking alarm 1 but remember to reset the alarm 2 selector switch back to buzzer/radio after the check has been completed. 1 2. Press the Alarm Set button to display the alarm 1 time. 1 Alarm Set 3. To check alarm 2 time, set the Alarm 2 selector switch to the buzzer or radio position.
Setting the alarms to wake to buzzer 1. Set the alarm time as previously described. Set the appropriate Alarm selector switch to the 'Buzzer' position. The corresponding Alarm indicators will light. 2. The buzzer alarm will sound every day at the preset time for 59 minutes. To switch off the alarm until the next day press the Off button. To switch off the alarms permanently set the Alarm selector switches to the 'Off' position.
Snooze control Snooze 1. The radio or buzzer alarm can be silenced for 7 minutes by pressing the Snooze button. This sequence can be repeated whilst the alarm is sounding. 1 Sleep timer The radio can be set to switch off after a preset time has elapsed. 1. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio will switch off after the sleep time has elapsed. Sleep Off 2 1 2.
Dimmer switch The Dimmer switch located on the underside of your clock radio will allow you to adjust the intensity of the clock display to suit room brightness. Headphone socket (on left hand side) A Headphone Socket (3.5mm) is provided for use with either headphones or an earpiece. Inserting a plug automatically mutes the loudspeaker.
General Fuse Do not allow this unit to be exposed to water or steam. It is recommended that the FM band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the MW band. This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug (BS1363). If another type of plug is used a 5A fuse should be fitted in the plug, adaptor or distribution board.
Specifications Circuit features Power Requirements Loudspeaker Mains AC 230 volts, 50Hz Back-up Battery IEC size 6F22/06PP (6LR61, PP3) Frequency Coverage Output power 350mW Aerial System FM 87.5 - 108MHz MW 540 - 1600 kHz 8 ohms only FM Wire Aerial MW Built-in Ferrite aerial The Company reserves the right to amend the specification without notice.
Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Receivers with removed or defaced serial numbers.
