Sound for Generations ROBERTS CR9952 Alarm Clock Radio Please read this manual before use
Contents Contents ............................................................................ 1 Controls .......................................................................... 2-4 Batteries ............................................................................ 5 Switching on and setting the time .................................... 6 Listening to the radio ........................................................ 7 Setting the alarm time ......................................................
Controls Front Back 5 6 4 3 7 2 8 1 1. Clock Display 6. Battery Cover 2. Minute hand 7. Light Mode button 3. Hour hand 8. Mains Supply Socket 4. Alarm hand 5.
Controls Top 13 12 11 14 10 15 9 9. Tuning scale 14. Alarm/Off button 11. Sleep button 15. Light/Off button 12. Snooze button 3 13. Speaker 10.
Controls Left hand side Right hand side 16 18 17 20 19 16. Time Set control 18. Tuning control 17. Alarm Set control 19. FM/MW switch 20.
Batteries 1. Press the On/Off button to switch the radio off before replacing batteries. 1 2. Open the battery cover located on the rear of your clock radio by pressing the catch down and pulling the battery cover towards you. 3. Insert 4 x AA batteries into the compartment. Make sure the (+) and (-) ends of the batteries are positioned as shown inside the compartment. 4. Close the battery cover. 2 5. Press the On/Off button to switch the radio on after batteries have been replaced. 6.
Switching on and setting the time Before using your alarm clock radio you must first set the correct time. 1. Check that the batteries have been installed correctly. 2. Place the unit on a flat surface. 3. Press in and turn the Time Set control.Rotating the control will move the clock hands, continue until the correct time is reached.
Listening to the Radio 1. Switch on the clock radio by pressing the On/Off button 2. Slide the FM/MW switch to the required waveband. 1 2 3. Tune in to the desired station by rotating the Tuning control. The station frequency is indicated in the Tuning scale. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. 3 For MW reception there is a built in ferrite aerial.
Setting the alarm time The alarm can be set to wake you by a buzzer. 1. Press the Alarm/Off button. 1 2. Press in and turn the Alarm Set dial. Rotating the dial will move the alarm hand, continue until the correct time is reached. The buzzer will sound at the preset time. After a few seconds the buzzer will sound more urgently and a few seconds later will change its tone again. 2 3. The clock display will turn to a Red backlight whilst the alarm sounds. 4.
Snooze control 1. The buzzer alarm can be silenced for 5 minutes by pressing the Snooze button. This sequence can be repeated during the 90 minute alarm period. 1 Sleep function 1. The radio can be set to switch off automatically after a preset time has elapsed. 2 2. Press the Sleep/Off button. The radio will stay on for 59 minutes, then turn off automatically. 3. If the Backlight is illuminated at the time of pressing the Sleep/Off button, the Backlight will change from green to blue.
Backlight The Backlight illuminates the clock display, making it easy to view in a dark environment. 1. Press and hold the Light/Off button on the top of the clock to turn on the Green backlight. The light will go off once the button is released.
Using the AC adaptor Your clock radio is supplied with a Mains Adaptor. 1. Place your clock radio on a flat surface. 2. Insert the adaptor plug into the DC socket located on the rear of your clock radio. 3. Plug the adaptor into a standard 13 amp mains socket outlet. Whenever the adaptor is used, the batteries are automatically disconnected. The AC adaptor should be disconnected from the mains supply and the radio when not in use. The AC adaptor for use with the CR9952 should provide 4.
Notes If you need any further advice, please call our Technical Helpline on :020 8758 0338 (Mon-Fri) 12
Specifications Circuit Features Power Requirements Mains Loudspeaker 8 ohms AC230 volts, 50Hz~ only Adaptor Output DC4.5 volts, 300mA Battery 4 x LR6 (AA Size) alkaline Output power 0.8 Watts Aerial System FM Wire Aerial MW Built-in Ferrite Aerial Frequency Coverage FM 87.5 - 108MHz MW 525 - 1605kHz The Company reserves the right to amend the specification without notice. General Do not allow this unit to be exposed to moisture (e.g.
Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Receivers with removed or defaced serial numbers.
ROBERTS RADIO TECHNICAL SERVICES 97-99 Worton Road Isleworth Middlesex TW7 6EG Issue 1 Technical Helpline:- 020 8758 0338 (Mon-Fri)
