Product Brochure

syringe to check for back
pressure at each hole. (Do
not weigh down floor; allow
adhesive to level itself
naturally.)
5) Plug each hole with one of
the dowels provided, to keep
the adhesive secured under
the floor. (Note: The dowels
will be slightly larger than
the holes and it will be
necessary to taper them
with a knife or sand
paper.) When in place, cut
each dowel even with the
flooring, then use the dowel punch to
lower it just below the surface. Once all dowels
are placed, the adhesive repair is complete and the
floor may be walked on immediately.
Clean Up: Clean up excess adhesive with a clean white cloth
dampened with soap and water. Dry adhesive can be cleaned with
mineral spirits or safety solvent. Wash out syringe and applicator tip
prior to storage.
Refer to material safety data sheet, www.robertsconsolidated.com
and industry standards prior to installation for additional information.
For installation questions that are not covered in this document please
contact our Technical Services Department at [phone].
Kit Contains:
• Wood Booster Repair Adhesive (1 quart)
• Applicator syringe (1)
with metal tips (2)
• Drill bits (2)
• Dowels (8) and dowel punch (1)
Roberts
®
R1550 Wood Booster Injection Repair Kit is designed as
a fast and easy solution to eliminate troublesome hollow spots and
loose areas in engineered wood flooring.
Features:
• Works instantly
• Floor can be walked on immediately
• Saves money on costly replacements
Enviro Friendly:
• Solvent Free • Zero VOCs (calculated)
Uses: For filling hollow spots due to too little adhesive being used, old
adhesive crystallizing due to the natural movement of the wood or
slight dips in the substrate beneath engineered wood floors.
General: Ensure substrate, flooring material and adhesive are fully
acclimated prior at the same temperature and humidity level expected
during normal use (between 65–95°F with a relative humidity (RH) of no
greater than 65%). Large temperature or humidity increases or
decreases can affect the flooring and performance of the installation.
Ensure adhesive original flooring adhesive is completely cured before
attempting to repair installation with the Wood Booster Injection
Repair Kit.
Ensure adequate ventilation during application.
Roberts R1550 adhesive is thin and may drip from the syringe even
when pressure is not applied.
In large areas some cupping may occur, but will dissipate after
several days.
Physical Characteristics (70°F, RH 50%):
Shelf Life: One year in unopened container
Storage: Protect from freezing
Application Instructions:
1) Place releasable blue tape around loose/ hollow area(s) to mark
them. It is best to repair all areas at once to prevent adhesive from
drying in the syringe.
2) In the areas outlined with blue tape, drill hole(s) with the 3/32 in. drill
bit provided. For areas 2 ft. or larger, drill a hole on each side of the
loose/hollow spot. The larger the area, the more drill holes required.
3) Stir adhesive. Attach one of the metal tips onto the syringe. To fill
syringe, separate plastic plunger from tube and pour adhesive into the
large open end of the tube, or transfer adhesive to a container and
draw it up into syringe.
4) Place syringe tip in the drilled hole and inject adhesive until back
pressure is felt, or for multiple hole areas inject until adhesive comes
out another hole. Ensure that all areas are completely filled by using
Roberts Consolidated Industries, Inc. • Boca Raton, FL 33487 • [phone] • www.robertsconsolidated.com
R1550
H2212_6860
WOOD BOOSTER
Injection Repair Kit
R1550-K 075378155010
DESCRIPTION PRODUCT # UPC
WOOD BOOSTER™
Injection Repair Kit
e
n
v
i
r
o
f
r
i
e
n
d
l
y
™