User Manual
Manuals
Brands
ROBO 3D Manuals
3D Printers
R1 Plus 10x9x8-Inch ABS/PLA 3D Printer, White (A1-0002-000)
1
2
3
4
5
6
7
8
9
10
Table Of Contents
41 CHAPTER VIII: Troubleshooting
CH II
Installing Software
CH III
Physically connect your printer
Connecting to the ROBO 3D Software
CH IV
Software Configuration for Printing
Navigating the home screen.
1. Queue
2. Library
3. History
4. About
5. Print Status
The Build Plate
1. Access to the Build Plate.
2. View Options
3. Positioning The Part
4. Adding Multiple Parts to One Build Plate
The Advanced Settings Panel
Controls
1. Adjusting Temperatures
2. Movement Controls
3. Speed Control
Slice Settings
Configuration
CHV
Configuring Slice Settings
SLICE ENGINES
Layers/ Perimeters
Layer Height:
First layer height:
Bottom Clip:
Avoid Crossing Perimeters:
Perimeters:
Top Layer:
Bottom Layer:
Infill
Fill density:
Infill Type:
Speed
Speed for Print Moves:
Speed for Non-Print Moves:
Skirt and Brim
Loops:
Distance from Object:
Minimum Extrusion Length:
Support Material
Generate Support:
Support Type:
Overhang Threshold:
Pattern Spacing:
Infill Angle:
Interface Layers:
X and Y Distance:
Z Gap:
Support Everywhere:
Create Raft:
Distance Around Object:
Air Gap:
Repair
Connect Bad Edges:
Close Polygons:
Reverse Orientation:
Merge All:
Output Options
Center On Bed:
Wipe Shield Distance:
Multiple Extruders
Support Material Extruders:
Advanced
First Layer Extrusion Width:
FILAMENT SETTINGS
Diameter:
Extrusion Multiplier:
Extrusion Temp:
Cooling
Enable Extruder Lift:
Min Fan Speed:
Max Fan Speed:
Bridging Fan Speed:
Disable Fan For The First:
Slow Down If Layer Print Time Is Below:
Min Print Speed:
PRINTER SETTINGS
Bed Size:
Print Center:
Build Height:
Bed Shape:
Has Fan:
Has Heated Bed:
Has SD Card Reader:
Z Can Be Negative:
G Code Output:
Custom G-Code
Start G-Code:
End G-Code:
Pause G-Code:
Resume G-Code:
Cancel G-Code:
Extruder 1
Nozzle Diameter:
Retraction Length:
Change Tool:
Z Lift:
Speed:
Minimum Travel Requiring Retraction:
Min Extrusion:
PRESETS
CHVI
Your First 3D Print (Workflow)
Obtain 3D Printable File
Computer Aided Design Software
Online
Upload File to MatterControl
Pre Heat
Set Slice Settings
Check Build Plate
Load Filament
Prep Build Plate
Run
CHVII
3D printing Resources
Makable.com
ROBO 3D Tech Support
CHVIII
Troubleshooting/ General Info
Heat
Adhesion
Warping
Clogging
Print Resolution
Cooling
Homing
Auto Leveling
Z Offset-Gaps in Bottom Surface
Overhangs- Support Material
Stringing- Retraction
Shifting Layers ad Irregular Circles
7
•
Reconnec
t your ROBO 3D afte
r this and pre
ss “Connect”
.
(
3.6a)
•
Once the printer con
nects, you wi
ll see a “Connection S
ucceeded!” mes
sage. From
her
e
click
“Done”.
(3.6b)
(3.6a)
(3
.6
b)
•
Your
ROBO 3D Prin
ter is c
onnected t
o the
so
ftw
are
!
1
...
...
5
6
7
8
9
...
...
48
