DM&P Group NCBox-189 User’s Manual
COPYRIGHT The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may contain in this document, and makes no commitment to update or to keep current information contain in this manual.
OWNER’S RECORD The serial number of this product is located at the rear panel of your NCBox series. Refer to the model and serial number when you contact your nearest dealer or DMP offices for services. SAFETY INFORMATION WARNING Do not expose NCBOX-189 to rain or moisture, in order to prevent shock and fire hazard. Never install NCBox-189 in wet locations. Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for qualified personnel servicing.
PURCHASE AGREEMENT PURPOSE: In accordance to the general commercial conduct of Trust and Fair Trade, herewith below is the agreement for the protection for both parties, DMP and Users in pursuant of trading. PRODUCT DESCRIPTION: With this product, herewith also known as NCBox-189, which is a simplified & an economical design of an embedded NCBox-189 for CNC machine.
Table of Contents CHAPTERS – HEADING PAGE NO. 0 – UNPACKING YOUR NCBOX ........................................................................................ 1 PACKING LIST ........................................................................................................ 1 CHECK BEFORE USE .............................................................................................. 1 1 – PREFACE ..................................................................................................
0 UNPACKING YOUR NCBOX Congratulation! You have just acquired NCBox-189, please check the following items: PACKING LIST FOR NCBox-189 SERIES Item Description NCBox-189 Q’ty 1 * Note: The accessories are subject to change without immediate notice.
1 PREFACE NCBox-189: The NCBox-189 is a complete computer, which is especially designed for CNC machine controller come with 2 parallel ports easy connect to your stepper driver, NCBox-189 support Microsoft Windows with the Mach3 CNC software and Linux with the LinuxCNC software, makes your CNC machine easiest install and control.
2 NCBOX-189 OVERVIEW Front Panel Power LED The power LED lights up when system is turn on. CF LED The CF LED flashes when the system is working. Never turn off the power when CF LED is still flashing. CF Slot The system is bootable from Compact Flash Card. 2nd Parallel Port 2nd Parallel Port (Port 378) USB port For connection to devices with USB interface (HDD, CD/DVD-ROM, Memory Stick, etc.
3 SYSTEM SPECIFICATION CPU Vortex86MX+ Keyboard and Mouse PS/2 Keyboard and Mouse Peripheral Main Memory 1. USB V2.0 x 3 1GB DDR2 2. Type I/II CF Slot BIOS AMI BIOS VGA D-Sub 15Pin Integrated Graphics Chip Powere Input DC 8V-24V 3. Parallel port x 2 4.
4 BIOS RECONFIGURING NCBox-189 1. Take note that AMI BIOS is used in the NCBox-189. To reconfigure the NCBox189, depress or hit the key to enter your BIOS setup main menu. 2. Select from the menu, the desired setup for change. 3. Press to go back to main menu. 4. Move “Exit” TAB and select “Save Settings and Exit”, press “Y” to save the changes that you just made. NCBox-189 will restart accordingly to your new setup.
ECHNICAL SPECIFICATION Model Processor NCBox-189 Vortex86MX+ Memory Onboard 1GB DDR2 VGA MIO Integrated Graphics Chip / D-Sub15-pin 10/100 Mbps LAN (RJ-45 connector) Built-in PXE diskless boot function CF Slot USB 3 ports (2 in the front) PS/2 Parallel Power 1 port (for KB/Mice) 2 Ports, 1 in rear (Port 278), 1 in front (Port 378) DC 8V ~ 24V Dimensions Weight 115x115x55 mm 500g Operation Temp. 5 – 50 Deg.
5 TAKING CARE NCBOX-189 This section gives you guidelines on using NCBox-189 – Safe using, Storing and Handling.
USING CABLES FOR CONNECTION To avoid problem, use only the specified interface cables in your accessory bag. The supplier will not be responsible for the connection arising from the other unspecified peripheral equipment. Do not use cut or damaged cables for connection. CLEANING YOUR NCBOX Clean the NCBox-189 with a soft, dry cloth or a soft cloth lightly moistened with a mild detergent solution.
6 TROUBLESHOOTING This section describes the techniques of resolving some basic problems that you encounter when using NCBox-189. For more troubleshooting guidelines, please contact your nearest dealer for technical support. TROUBLESHOOTING YOUR NCBOX A. NCBox does not start Make sure the NCBox-189 is properly secured and plugged into a power source before it is turned on. Make sure the power indicator shows the power is on. See section 2 for more information about “NCBox-189 Overview”.
B. BIOS Error Message – BIOS error message appear when my NCBox starts If the BIOS error message appears, press any key to resume or, hit to enter BIOS setup main menu, follow these steps: 1. Press , and the BIOS Setup main menu appears, check if CF Card is detected at “Pri Master”. If it is not detected, use Direction keys <↑↓> to choose “AUTO” and then go back to the main menu by pressing .
C. “Operating System Not Found” – A message indicating that “Operating system not found” appear when my NCBox starts Enter your BIOS setup main menu by pressing key, be sure that the C: drive is enable. If OS still does not start, follow these steps to initialize the BIOS: 1. Turn off the NCBox-189. 2. Remove any peripheral devices connected to the NCBox-189. 3. Restart the NCBox-189.. 4. Press to enter BIOS Setup main menu window. 5. Follow the steps as written in item B.
To obtain an RMA number, Purchaser must follow procedures as below： A. Complete the DMP Electronics Inc. standard RMA Form and fax back to the RMA Department. B. The RMA Number must be used within 7 DAYS C. The RMA Number must be shown clearly on your shipping label. D. DMP Electronics Inc. must receive all Returns before a replacement will be sent. E. The repair cost is depends on the parts, the damage reasons, and whether under warranty period…etc.
MEMO NCBox-189 13
