RBT3.0 Learning SMART LOCK Installation Guide 1 To Custermer 4 2 3 5 6 7 8 9 ＊ 0 ＃ Instruction Manual ■ Before use Please read this manual thoroughly in order to use this product properly. Please keep this in case that a problem occurs. * Please do not reprint or copy the contents of this manual without permission. ※ The appearance and specifications shown are subject to change without prior notice for improvement. ※ The compensation for errors etc. described in this manual will not be made.
Table of contents Before use Advanced features ・・・・・・・・・・・・・・・・・・3 Items included ・・・・・・・・・・・・・・・3 Register master card ・・・・・・2 3 ・・・・・・2 4 Notice before use ・・・・・・・・・・・・4 Register user card About this product ・・・・・・・・・・・・6 Deletion of user card Name of parts Initial set up（Tablet） Silent mode Pincode registration Notification of low battery ・・・・・・2 9 Pin code Emergency power supply ・・・・・・2 9 ・・・・・・・・・・・・1 0 Reset the device by using ・・・・・・・・・・・・・・・・・・1 0 Open/Close button Thumb turn
Before Use Please read this manual thoroughly in order to use this product properly. ■ Items included Please check the below items are included in this package. ※The below figures may look slightly different from they actually are.
Before Use Please read this manual thoroughly in order to use this product properly. ■ Notice before use ●Please keep your physical key in case of emergency. ●Please use unused Alkalin batteries. Otherwise, it may shorten the battery life, or worse, cause the device failure. ●It's recommended to replace batteries once a year. It is also recommended to operate the lock a few times a month at least since leaving it unused with batteries loaded may causes liquid leaks of the batteries.
Before Use Please read this manual thoroughly in order to use this product properly. ■ Notice before use ●Since prepaid transportation cards may be replaced when you update it, please register another card for your back up. Also, do not use Korean prepaid transportation card nor Smartphones which may share its ID with another card/ device. ●Do not bend, make holes on, nor expose high temperature the device. ●You can use AC power supply with batteries loaded.
Before Use Please read this manual thoroughly in order to use this product properly. ■ Notice before use Modification warning Caution! ● Any changes or modifications (including the antenna) made to this device that are not expressly approved by the manufacturer may void the user s authority to operate the equipment.
Before Use Please read this manual thoroughly in order to use this product properly. ■ About this product ●This product is an electronic device that can control many types of locks via various way such as blue tooth, IC card, and personal pincode. 1. How to use ●IC card（Master card (up to 5), User card (up to 300)）。 ●Your personal pincode ●Bluetooth （Application is required）。 ●Physical key 2. How to use ●when you go out Push ＃ and ＊ in this order to lock the door.
Before Use Please read this manual thoroughly in order to use this product properly. ■ About this product 3. Features ●Bluetooth Control the device remotely via kit application ●IC card IC cards conforms to international standards such as ISO14443A, ISO15693, ISO18092 can be registered as a master card. ※Some IC card cannot be registered depending on their quality. ●Autolock By using this feature, the door will be closed automatically 1 sec after you close the door.
Name of parts IC reader unit Thumb turn/battery unit IC reader region the region to hold IC card up over Battery unit cover This cover is for protecting battery and operation buttons. Slide it up to get off. Start-up key Key to start the device ※Pressing any key can start the device Emergency power supply terminal The terminal to supply power through when the battery is out. Key Cylinder cover This cover is for protecting Emergency power supply terminal. Slide it down to get off.
Initial set up（Tablet） ■ Pincode registration You can unlock the door with your pincode even if you don't have smartphone nor IC card with you. This is also needed during the authentication process performed on the tablet. Prerequisit１： it uses Bluetooth®. The distance between the tablet and the lock should be within 10m.
Basic feature ■ Pin code ■ IC card Hold IC card after start-up key to unlock the door. Please follow the below procedure to use your pincode Start-up key The button you press firstly ※Start-up key can be any button on the key pad. The button you press lastly IC reader ※Sensitivity differs on its quality and kind. Please use sensitive one to register.
Basic feature If you don't use autolock, the door will be locked when you press ＃ and ＊ in this order. ■ Open/Close button ■ Thumb turn Open/Close button Thumb turn Step１ Push Open/Close button Step１ Like ordinary thumb turns, you can lock and unlock by turing it.
Use from kit app（Tablet） If you don't use autolock, the door will be locked when you press ＃ and ＊ in this order. ■ Lock ・Unlock Prerequisit１： The lock should be paired with the tablet. Please refer to p22.Pairing ①Tap the button of Smart lock card on the tablet ②unlocked 閉まっています 開いています ※The screen shot shown may be different from actual one depending on the version of the lock you use.
Use from kit app（Tablet） ※Registration of all IC card will be canceled if you perform set-up procedure from kit app. ■ IC card registration Prerequisit１： it uses Bluetooth®. The distance between the tablet and the lock should be within 10m.
Use from kit app（Tablet） ■ Change your pincode Prerequisit１： it uses Bluetooth®. The distance between the tablet and the lock should be within 10m.
Use from kit app（Tablet） ■ Auto lock The device lock itself spontaneously if you left the door closed after unlocking it. This happens even if you don't use Auto lock feature. Prerequisit１： it uses Bluetooth®. The distance between the tablet and the lock should be within 10m.
Use from kit app（Tablet） ■ Pairing Prerequisit１： it uses Bluetooth®. The distance between the tablet and the lock should be within 10m. Prerequisit２： Register your personal pincode to the lock.Please refer to p15.
Advanced features ■ Register master card Register master card Prepare master card（up to 5 cards can be registered） Procedure Prepare IC card Push C Step1 Push C button twice Uncover the battery unit and push C button once then you will hear "pit pit pit lot lot" Uncover the battery unit Push C button "pit" Push C button again "pit" "pit lot lot lot" Step２ Hold your IC card Hold your IC card up over IC reader unit, you will hear "pit pot" and the card is registered as a master card.
Advanced features ■ Register user card Register user card Contrary to master card managing all the registered info, up to 300 user cards can be registered to one device. This can be used to allow your colleague or family members to open the door. ※Some IC card cannot be register due to its low quality. Push ＊ and hold your card you want to register. If you hear "pii pii pii", your card is compatible. Otherwise it's not.
Advanced features ■ Deletion of user card １ Delete an individual IC card You can delete a card individually by its block number. If the block number is unknown, you cannot delete it individually. ※You cannot delete multiple cards at once.
Advanced features Easy to set up via kit app! ■ Deletion of user card ※Registration of all IC card will be canceled if you perform set-up procedure from kit app.
Advanced features Easy to set up via kit app! ■ Deletion of master card ※Registration of all IC card will be canceled if you perform set-up procedure from kit app. Deletion of master card Prepare your master card ※All the registered mastercards will be deleted if you delete one of them. User card will not be deleted. ※Your personal pincode will be deleted if you delete your master card. Procedure Step１ Hold Ｃ button for 5-10 sec Push C R Uncover the battery unit and hold Ｃ button for 5 sec.
Advanced features ■ Silent mode Emergency alart cannot be muted. You can mute the sound by using this feature. In the default setting, the device gives sounds. Step１ Remove a battery Remove one battery by uncovering the battery cover. Step２ Change the 3rd dip switch to ② Change the 3rd dip swithch to ② with a screw driver as shown below.
Other features ■ Notification of low battery No need to set up for this. When batteries are low, LED of Open/Close button blinks and the melody of twinkle twinkle little star gives you an alart. ※You can use the lock approx. 300times after this alart starts. But it's recommended to change all the batteries at once as soon as possible. When you change batteries, please push Open/Close button several times to discharge the standby current.
Other features ■ Alart ■ Reset the device by using emergency power supply terminal For countermeasure against invasion, this device gives off an alart sound more than１００ｄＢ. This can be occured in case the magnet accidentaly come off, someone try opening the door before unlocking or opening the door just before it closes. In case the device is freezed by static electoricity or other reasons, the device can be reset by supplying power from the emergency terminal.
Specification Model RBT3.0 Main unit 65×140×53mm IC reader unit 55×105×29mm Power supply AAA Alkaline batteries（use 10 times a day=aprox.
Specification ■ Compatible lock cases MIWA LA、LAF、BH DA、DAF POSTE、LSP、LE、TE、FG PP POM Others, OEM Locks GOAL LX series, LG series, LDseries, others SHIBUTANI CDS series、LCS series Compatible backset length 38、51、64、76mm Compatible door thickness 30 〜 60mm ※the door with the thickness more than described left can be compatible with special adaptors. ■All the data is collected under the conditions determined by RobotHome. The content can be changed without prior notice.
Robot Home Co.,Ltd. Learning SMART LOCK For more information, visit robothome.co.jp Company outline Robot Home Co., Ltd.
