100MM MXS 3D V2 SPORT 3D ACROBATIC RIGID STRONG DURABLE EPO LIGHT HOLLOW WING DESIGN FMSMODEL.
WARNING WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product. personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision.
Table of Contents Introductions..................................................................................................................................................2 Contents of Kit...............................................................................................................................................3 Assemble the plane.......................................................................................................................................
Wingspan: 1100mm (43.3in) Overall Length: 1114mm (43.85in) Flying Weight: Around 1180g(41.6oz) Motor Size: Brushless 3541-KV1230 Wing Load: 30.3 g/dm² (0.068oz/in²) Wing Area: 26.12 dm² (405.9sq.in) ESC: 40A Servo: 9g metal digital Servo x 4 Recommended Battery: 11.1V 2200mAh 25C Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels.
Assemble the plane 1. Unpack the elevator parts bag and assemble PA 2.3*10 mm and connecting pipe as shown in Figure 1 and 2. KA2.6*12mm fig1 fig2 2. Install the elevator servo arms and linkage rods as shown in Figures 3 and 4. fig4 fig3 3. Attach the main landing gear using 3 PM 3.0 X 10mm screwsas shown in Figure 5. 4. Find the Y-harness and connect it to both aileron servos.Connect the Y-harness to the receiver, then place the receiver into the fuselage as shown in Figure 6 . HKM 3.
5. Assemble the main wing as shown in Figure 7. Use four screws to lock the wing as shown in Figure 8. HKM 3.0 x 20 fig8 fig7 6.Glue on the Vortex Generator on the wing tip using the applied glue (fig9). fig9 Install the battery and Radio installation 1. Apply the hook tape to the cable end of the battery (fig10). 2. Slide the battery into the battery hatch with the power supply cable toward the rear end of the plane and the hook tape facing the bottom of the battery hatch.
Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): 30 25 70 20 18 40 Tips: At first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds. High rate, as listed, are listed, are only for EXTREME maneuvering. Check the motor rotating direction The motor should rotate clockwise when viewing the plane from the rear.
Linkage rod Installation Press the socket-style linkage connector over the corresponding ball end on the control horn. Control Horn and Servo Arm Settings The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes. After flying, you may choose to adjust the linkage positions for the desired control response.
Install the propeller and spinner Assemble the spinner and propeller as shown below. e d c b a Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people especially children who can wander unpredictably.
Flying course Take off While applying power, slowly steer to keep the model straight. the model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. MXS 3D will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Troubleshooting 12
Spare parts list content ROCKL101 ROCKL102 ROCKL103 ROCKL104 ROCKL105 ROCKL106 ROCKL107 ROCKL108 ROCKL109 ROCKL110 ROCKL111 ROCKL112 FMSPROP047 FMSDJ009 FMSBM026 FMSDZ010 PRKV1230 FMSESC40A200 FMSSER9MGDP Fuselage Main Wing Set Horizontal Stabilizer Cowl Battery Hatch Main Landing Gear Set Rear Landing Gear Set Spinner Set Linkage Rod Vortex Generator Decal Sheet Pipe Set Propeller Motor Mount Motor Board Propeller Adapter 3541-KV1230 Motor 40A ESC(200mm input cable) 9g digital metal gear servo positive V
ESC instruction Battery Pack A quality connector is essential ESC Brushless Controller Receiver 14 Motor
