RF-SBM101_13-0263_MAN_V1_ENG.fm Page 1 Monday, May 6, 2013 10:53 AM RF-SBM101 Soundbar Mount User Guide Safety information and specifications ........ 2 What you need .................................................... 4 Package contents: parts ................................... 4 Package contents: hardware .......................... 5 Installation instructions.................................... 7 Before using your new product, please read these instructions to prevent any damage.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 2 Monday, May 6, 2013 10:53 AM Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Maximum soundbar weight: 15 lbs. (6.8 kg) Overall dimensions (W × D × H): 1.75 x 1.0 x 11.9 in. (4.4 x 2.5 x 30.2 cm) Soundbar mount weight: 1.74 lbs. (0.79 kg) We’re here for you www.rocketfishproducts.com For customer service, call: 800-620-2790 (U.S.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 3 Monday, May 6, 2013 10:53 AM Before You Begin Please check the following items: • Your TV and any accessories you plan to use do not exceed the specified weight limit of your TV mount. • You read and understand these directions. • You refer to the documentation that came with your TV for additional guidance. • You have the tools needed for installation.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 4 Monday, May 6, 2013 10:53 AM What you need You will need the following to assemble your new sound bar mount: Phillips screwdriver TV Wall Mount Bracket Level Package contents: parts Make sure that you have all the parts necessary to assemble your new sound bar mount.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 5 Monday, May 6, 2013 10:53 AM Package contents: hardware Make sure that you have all the hardware necessary to assemble your new soundbar mount.
RF-SBM101_13-0263_MAN_V1_ENG.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 7 Monday, May 6, 2013 10:53 AM Installation instructions STEP 1: Option 1 - Mount the bracket arms to the soundbar 1 Check the compatibility of the soundbar bracket with your soundbar. 2 Insert the keyhole screws (D) into the knobs (E). 3 Attach the soundbar arms (A) to your soundbar with the assembled knob/keyhole screws. NOTE: When planning on the position of the soundbar, make sure you will be able to properly access control buttons, if necessary.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 8 Monday, May 6, 2013 10:53 AM 4 [OPTIONAL] If there are gaps or recesses under the soundbar arms, slip a “Fender” washer (C) onto the keyhole screws (D) and under the soundbar arms (A) make sure that the soundbar arms (A) lay flat on the soundbar. A C E 5 Loosely tighten the knobs (E).
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 9 Monday, May 6, 2013 10:53 AM STEP 1: Option 2 - Mount the bracket arms to a hanger Some soundbars come with a manufacturer supplied hanger (for example Samsung). 1 Attach the soundbar arms (A) to the soundbar hanger with the assembled knob/keyhole screws. Do not fully tighten knobs.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 10 Monday, May 6, 2013 10:53 AM STEP 2 - Preparing your TV (go to Step 3 if your TV is not already mounted on the wall). CAUTION: Refer to your TV wall mount assembly instructions for how to properly remove your TV from the brackets. 1 Remove all cables attached to your TV. 2 Remove your TV from the wall. 3 Remove the existing wall mount bracket from the back of your TV.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 11 Monday, May 6, 2013 10:53 AM CAUTION: Heavy. You may need assistance with this step.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 12 Monday, May 6, 2013 10:53 AM STEP 3 - Determine whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. 2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions. 3 Temporarily lay your existing TV wall mount brackets (not included) on the back of your TV.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 13 Monday, May 6, 2013 10:53 AM • Obstructed back: A bracket blocks any of the jacks on the back of your TV. You will need spacers when assembling the wall mount. • Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You will need spacers when assembling the wall mount. 6 Remove the TV brackets.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 14 Monday, May 6, 2013 10:53 AM STEP 4 - Select screws, washers, and spacers 1 Select the hardware necessary for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the correct length and diameter of the mounting screws your TV requires, test various sizes by hand threading the screws.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 15 Monday, May 6, 2013 10:53 AM Screw fits correctly Screw is too long Screw is too short 2 Remove the screws. 3 For a flat back TV, go to “STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back” on page 16. -ORFor an irregular or obstructed back, go to “STEP 5 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs” on page 18.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 16 Monday, May 6, 2013 10:53 AM STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back 1 Place the mount spacers (F) over the top two screw holes on the back of the TV. 2 Place the TV bracket arms (B) over the bottom two screw holes on the back of the TV. To make sure the arms are not visible when on the wall, align the arms so they reach the bottom or corners of the TV, but do not over hang the edges.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 17 Monday, May 6, 2013 10:53 AM 6 Tighten all screws, but do not over-tighten. NOTE: Your existing TV wall mount may vary from the one shown below. Refer to the instructions that came with your existing TV wall mount for attaching brackets to the bac of the TV. However, you MUST use the screws and washers provided with the soundbar mount instead of the screws and washers that came with your existing wall mount.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 18 Monday, May 6, 2013 10:53 AM STEP 5 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Place the spacers (N) and mount spacers (F) over the top two screw holes on the back of the TV. 2 Place the spacers (N) and the TV bracket arms (B) over the bottom two screw holes on the back of the TV.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 19 Monday, May 6, 2013 10:53 AM 6 Tighten all screws, but do not over-tighten. NOTE: Your existing TV wall mount may vary from the one shown below. Refer to the instructions that came with your existing TV wall mount for attaching brackets to the back of the TV. However, you MUST use the screws and washers provided with the soundbar mount instead of the screws and washers that came with your existing wall mount.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 20 Monday, May 6, 2013 10:53 AM STEP 6: Options 1 and 2 - Attach the soundbar assembly to your TV CAUTION: The ends of the TV/bracket arms (A) must not extend beyond the edge of the TV. • Attach the soundbar bracket arm (A) assembly to the TV bracket arm (B) assembly with two knobs (E). Do not fully tighten the connections.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 21 Monday, May 6, 2013 10:53 AM STEP 6: Option 3 - Attach the soundbar hanger assembly to your TV • Attach the soundbar bracket arm (A) and hanger assembly to the TV bracket arm (B) assembly with two knobs (E). Do not fully tighten the connections.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 22 Monday, May 6, 2013 10:53 AM STEP 7 - Final adjustments, tightening, and hanging the TV 1 Adjust the soundbar bracket arm (A) assembly and the TV bracket arm (B) until the soundbar is in the position you want. NOTE: The soundbar must be positioned within 2 inches (5.1 cm) of the TV. CAUTION: Heavy. You may need assistance with this step. 2 in. (5.1 cm) Attaching the soundbar using the manufacturers supplied bracket.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 23 Monday, May 6, 2013 10:53 AM NOTE: The TV/bracket arms should be positioned as vertically as possible. 2 When the soundbar is in the correct position, tighten all fasteners.
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 24 Monday, May 6, 2013 10:53 AM 3 Hang the TV/soundbar assembly on the wall, following the instructions that came with your existing TV wall mount, then reconnect the cables and power cord. You’ll need Phillips screwdriver For customer service, call: 800-620-2790 (U.S./Canada markets) or 01-800-926-3010 (Mexico).
RF-SBM101_13-0263_MAN_V1_ENG.fm Page 28 Monday, May 6, 2013 10:53 AM www.rocketfishproducts.com (800) 620-2790 Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN 55423-3645 USA © 2013 BBY Solutions, Inc. All rights reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective owners.
